Emerson Rosemount 5900C Скачать руководство пользователя | Manualshive

Страница: 138 / 322

background image

4.6

LPG configuration

4.6.1

Preparations

Prerequisites

Before starting configuration of the Rosemount

™

5900C for LPG measurements, ensure

that all mechanical installations are made according to instructions, and all external
sensors such as pressure and temperature sensors are properly connected.

For Rosemount 5900C with F

OUNDATION

™

Fieldbus the LPG Setup is described in

using DeltaV / AMS Device Manager

Highly pressurized vapor above the product surface affects the propagation speed of
microwaves. The Rosemount 5900C level gauge is able to compensate for this, thus
avoiding deviations in measured level due to the vapor.

When the gauge is installed on the empty tank, calibrate the gauge and configure for LPG
measurements.

To install a Rosemount 5900C for LPG measurements perform the following major steps:

Procedure

1. Install the tank and the Rosemount 5900C level gauge in Rosemount TankMaster

WinSetup as described in the Rosemount Tank Gauging

System Configuration

. Ensure that the appropriate tank and device types are selected, and the

temperature and pressure sensors are properly configured. Check that the gauge
communicates with the TankMaster PC.

2. Install the Rosemount 5900C gauge on the still-pipe. Measure the exact distance to

the Verification Pin.

3. Configure the Rosemount 5900C according to the standard procedure for a

Rosemount 5900C level gauge (see the Rosemount Tank Gauging

Configuration Manual

). Rosemount TankMaster Winsetup is the recommended

configuration tool.

4. Configure the vapor pressure sensor.
5. Set Correction Method to Air Correction Only.
6. Calibrate the Rosemount 5900C.
7. Configure the Verification Pin.
8. Verify position of Verification Pin.
9. Set up the Correction Method that applies to the particular type of product in the

tank.

The LPG installation procedure using Rosemount TankMaster Winsetup is described
in section

LPG setup using Rosemount

.

Configuration

Reference Manual

September 2019

00809-0100-5901

138

Reference Manual

«
...
136
137
138
139
140
...
»

Содержание Rosemount 5900C



































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount 5900C

DVCPRO P2 Series

Бренд: Panasonic Страницы: 32

Бренд: NAD Страницы: 10

Бренд: PANDROL Страницы: 36

Бренд: Federal Signal Corporation Страницы: 2

Бренд: Harman Kardon Страницы: 7

Бренд: OceanSat Страницы: 85

Бренд: Malekko Страницы: 2

Бренд: Major Страницы: 26

Бренд: OHAUS Страницы: 84

Бренд: Raven Страницы: 48

Бренд: Pacific Страницы: 16

FUSION APOLLO MS-WB675

Бренд: Garmin Страницы: 18

Бренд: Rapid Shape Страницы: 12

MultiFill 003-561-005

Бренд: Hanskamp Страницы: 20

Бренд: TANNER Scientific Страницы: 44

Бренд: ProLights Страницы: 28

Monolith NT.115

Бренд: Nano Temper Страницы: 24

SCAFFOLDBENCH I-CISRL

Бренд: MetalTech Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды