Emerson Rosemount 2240S Скачать руководство пользователя страница 49

Страница: 49 / 194

Reference Manual

00809-0100-2240, Rev DA

Rosemount

™

2240S Installation

October 2017

Rosemount

™

2240S Installation

4.4.8

Rosemount

™

2240S in F

OUNDATION

Fieldbus system

The Rosemount 2240S supports the F

OUNDATION

fieldbus (FF) technology and lets you integrate a

Rosemount 2240S into an existing FF network. As long as the power supply meets certain requirements
(see

Figure 4-4

and

Figure 4-5

) the 2240S

(1)

will be able to operate as any other FF device.

Figure 4-4. Example of an I.S. F

OUNDATION

fieldbus System with Rosemount Devices

Ensure that the power supply is able to provide the total current needed for all the connected devices.
See

“Power requirements” on page 33

for further information.

Ensure that the Rosemount 2240S and other devices connected to the F

OUNDATION

fieldbus (FF) system

are compliant with the FISCO or Entity parameters of the power supply.

Ensure that the short circuit protection of the Segment Coupler

(2)

matches the current consumption of

the connected devices.

Figure 4-5. Example of a Non-I.S. F

OUNDATION

Fieldbus System with Rosemount Devices

1, See

Appendix B: Product Certifications

for Rosemount 2240S approval information

See the Rosemount 2410 Reference Manual (Document No. 300530EN) for more information on the Segment Coupler.

Rosemount 5900S
Radar Level Gauge

Rosemount 2240S
Temperature Transmitter

Rosemount 2230 Display

FISCO/Entity compliant

FM USA, FM Canada:
AIS Class I, Division 1

ATEX and IECEx:
Ex [ia], or Ex [ib] (FISCO)
Ex [ia] (Entity)

Segment
Coupler

I.S. Power Supply

Trunk

Barrier

IS Trunk

SAFE AREA

HAZARDOUS AREA

Segment
Coupler

Non-I.S. Power Supply

FISCO/Entity compliant

FM USA, FM Canada:
AIS Class I, Division 1

ATEX and IECEx:
Ex [ia], or Ex [ib] (FISCO)

Rosemount 5900S
Radar Level Gauge

Rosemount 2240S
Temperature Transmitter

Rosemount 2230 Display

Содержание Rosemount 2240S



































































































































































































Результаты поиска

Содержание Rosemount 2240S

Отзывы:

Emerson Rosemount 2240S, Справочное руководство, Страница: 49 / 194

Результаты поиска

Содержание Rosemount 2240S

Отзывы: