Emerson Numatics G2-2 ControlNet Series Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 11

Emerson Numatics G2-2 ControlNet Series Скачать руководство пользователя страница 8

G2-2 Series ControlNet

Quick Start Manual

Page 8

TDG22CNQS4-0

1/07

Subject to change without notice

www.numatics.com/fieldbus

9) Auxiliary Power Connector Pin-Out

Pin No.

Function

Description

1

+24VDC

(Valves and Outputs)

Voltage Used to Power Outputs
(Valve Coils and Discrete Outputs)

2

Earth Ground

Protective Earth (Case Ground)

3

0VDC Common

0VDC Common, for Valves, I/O, and Node Power

4

+24VDC

(Node and Inputs)

Voltage Used to Power Discrete Inputs and Node Electronics

!

•

Maximum current capacity on the 0VDC common pin of the auxiliary
power connector is 8 Amps. The combined draw of the +24VDC Valves and
Outputs and +24VDC Node and Inputs pins cannot exceed 8 Amps, at any
given moment in time.

•

The auxiliary power +24VDC Node and Inputs pin supplies power to the
node electronics. This pin must be powered at all times for communication
node to be functional.

4

1

3

2

«
...
6
7
8
9
10
...
»

Содержание Numatics G2-2 ControlNet Series












Отзывы:

Нет отзывов