Emerson Neotecha Sapro Скачать руководство пользователя страница 4

4

Neotecha

 Sapro Sampling DeviceS

Maintenance and RepaiR instRuctions

Figure 5

Figure 6

Figure 7

Figure 8

2-pin wrench

valve Seat replacemeNt

a) Bottle adaptor models

1. 

Wafer body design

 

(See Fig. 5 and Fig. 6)

 

You will need: repair kit - Sv-Set 1 and 
Tool kit - Sv-W2.

1.1. Take the Sapro valve from the pipe line.
1.2. loosen the socket head screw (1d) and 

remove the safety claw (1c).

1.3. Unscrew and remove bottle adaptor (5a).
1.4. loosen the set screw (1a).
1.5. Using the 2-pin wrench (provided in Tool 

kit Sv-W2), unscrew the retaining ring (5), 
to reveal the valve seat assembly o-ring 
(3a), soft seal (3) and valve seat (4).

1.6. clean the bottle adaptor, valve seat and 

retaining ring.

1.7. replace the o-ring (3a) and seat seal (3) 

with new parts from the repair kit Sv-Set 1.

2. 

Flanged body design

 

(See Fig. 7 and Fig. 8)

 

You will need: repair kit - Sv-Set 1 and 
Tool kit - Sv-W2.

2.1. Take the Sapro valve from the pipeline.
2.2. loosen the three set screws (5a) and 

withdraw the bottle adaptor assembly.

2.3. remove the four socket head screws (1a) 

and withdraw the retaining flange (5) to 
reveal the valve seat assembly o-ring (3a), 
soft seal (3) and valve seat holder (4).

2.4. clean the bottle adaptor, retaining flange 

and valve seat.

2.5. replace the o-rings (3a, 5d) and seat 

seal (3) with new parts from the Seal kit 
Sv-Set 1.

2.6. reassemble by reversing the above 

procedure.

Содержание Neotecha Sapro











Отзывы: