manualshive.com logo in svg

Emerson MW9107W, Руководство по обслуживанию, Страница: 1 / 37

Поделиться
Скачать
Emerson MW9107W Скачать руководство пользователя страница 1

SERVICE MANUAL

CAUTION: Before servicing the chassis, read the Safety and Precautions  section on page 1 of this manual.

Note: All the specifications and features are subject to change without notice.

Copyright 2004 Emerson Radio Corp. All rights reserved.

EMERSON RADIO CORP.
Parsippany, NJ 07054

SPECIFICATIONS

POWER SUPPLY................................120V 60Hz AC, 12A SINGLE

PHASE WITH GROUNDING

POWER CONSUMPTION.......................................................1400W

MICROWAVE OUTPUT POWER...........................................1000W

OUTSIDE DIMENSIONS.......................21.2(W) x 16.0(D) x 11.8(H)

CAVITY DIMENSIONS............................13.9(W) x 14.7(D) x 9.0(H)

CAVITY VOLUME...............................................................1.1 CU.FT

NET WEIGHT ...................................................34.2 LBS (APPROX.)

TIMER..........................................................................59 min. 99 sec.

CONTENTS

SAFETY AND PRECAUTIONS  ...................................................... 1

1. FOR SAFE OPERATION .......................................................... 1
2. FOR SAFE SERVICE PROCEDURES  ................................... 1

EXTERNAL VIEW  ............................................................................ 2

1. OUTER DIMENSION  ................................................................ 2
2. FEATURE DIAGRAM ................................................................ 3
3. CONTROL PANEL  .................................................................... 4

INSTALLATION.................................................................................  5

OPERATIONS AND FUNCTIONS  ................................................. 6

DISASSEMBLY AND ASSEMBLY  ................................................. 7

INTERLOCK MECHANISM AND ADJUSTMENT ....................... 14

TROUBLESHOOTING GUIDE ...................................................... 15

MEASUREMENT AND TEST  ....................................................... 19

1. MEASUREMENT OF THE MICROWAVE POWER OUTPUT ....... 19
2. MICROWAVE RADIATION TEST .......................................... 20
3. COMPONENT TEST PROCEDURE  ..................................... 21

PRINTED CIRCUIT BOARD .......................................................... 24

1. CIRCUIT CHECK PROCEDURE ........................................... 24
2. P.C.B. CIRCUIT DIAGRAM ..................................................... 29
3. COMPONENT INFORMATION .............................................. 30
4. PRINTED CIRCUIT BOARD ................................................... 31
5. P.C.B. LOCATION NO ............................................................. 32

WIRING DIAGRAM ........................................................................ 22

EXPLODED VIEW AND PARTS LIST  ......................................... 33

1. DOOR ASSEMBLY  ................................................................. 33
2. CONTROL PANEL ASSEMBLY  ............................................ 33
3. TOTAL ASSEMBLY  ................................................................ 33

SERVICE PUBLICATION

MODEL

MW9107W/WC

Содержание MW9107W






































Отзывы:

Нет отзывов