Emerson Micro Motion 3350 Скачать руководство пользователя страница 2

Страница: 2 / 25

Safety and approval information

This Micro Motion product complies with all applicable European directives when properly installed in accordance with the

instructions in this manual. Refer to the EC declaration of conformity for directives that apply to this product. The EC declaration of

conformity, with all applicable European directives, and the complete ATEX Installation Drawings and Instructions are available on

the internet at

www.micromotion.com

or through your local Micro Motion support center.

Information affixed to equipment that complies with the Pressure Equipment Directive can be found on the internet at

www.micromotion.com/documentation

For hazardous installations in Europe, refer to standard EN 60079-14 if national standards do not apply.

Other information

Full product specifications can be found in the product data sheet. Troubleshooting information can be found in the transmitter

configuration manual. Product data sheets and manuals are available from the Micro Motion web site at

www.micromotion.com/

documentation

Return policy

Micro Motion procedures must be followed when returning equipment. These procedures ensure legal compliance with government

transportation agencies and help provide a safe working environment for Micro Motion employees. Failure to follow Micro Motion

procedures will result in your equipment being refused delivery.

Information on return procedures and forms are available on our web support system at

www.micromotion.com

, or by phoning the

Micro Motion Customer Service department.

Emerson Flow customer service

Email:

•

Worldwide:

[email protected]

•

Asia-Pacific:

[email protected]

Telephone:

North and South America

Europe and Middle East

Asia Pacific

United States

800-522-6277

U.K.

0870 240 1978

Australia

800 158 727

Canada

+1 303-527-5200

The Netherlands

+31 (0) 704 136 666 New Zealand

099 128 804

Mexico

+41 (0) 41 7686 111 France

0800917901

India

800 440 1468

Argentina

+54 11 4837 7000

Germany

0800 182 5347

Pakistan

888 550 2682

Brazil

+55 15 3413 8000

Italy

8008 77334

China

+86 21 2892 9000

Venezuela

+58 26 1731 3446

Central & Eastern

+41 (0) 41 7686 111 Japan

+81 3 5769 6803

Russia/CIS

+7 495 981 9811

South Korea

+82 2 3438 4600

Egypt

0800 000 0015

Singapore

+65 6 777 8211

Oman

800 70101

Thailand

001 800 441 6426

Qatar

431 0044

Malaysia

800 814 008

Kuwait

663 299 01

South Africa

800 991 390

Saudia Arabia

800 844 9564

UAE

800 0444 0684

Содержание Micro Motion 3350


























Результаты поиска

Содержание Micro Motion 3350

Отзывы:

Похожие инструкции для Micro Motion 3350

Бренды по названию

Популярные бренды

Emerson Micro Motion 3350, Руководство по установке

Результаты поиска

Содержание Micro Motion 3350

Отзывы:

Похожие инструкции для Micro Motion 3350

Бренды по названию

Популярные бренды