Emerson Liebert NXL 250 kVA Скачать руководство пользователя

Страница: 87 / 112

UPS Alarm and Status Messages

Liebert

NXL

™

PPENDIX

A - UPS A

LARM

AND

TATUS

ESSAGES

Table 10

shows alarm and status messages as they appear in the Liebert NXL’s touchscreen and in

the history log, along with a description and recommended actions, if any.
If the recommended action fails to correct the condition, contact your factory-authorized service pro-

vider.
The “Service Telephone Number” can be found by pressing “CONFIG,” “Ratings,” “More>>” on the

menu bar.

NOTE

In Event log, take the number for the “Data” Column. Convert that number from Decimal to

Hex. Each digit will explain the reason for the Inhibit signals.
Example:

Data = 512d =0200h->“Removing Module will cause Overload or Drop the Load”

Table 10

Liebert NXL alarm and status messages

Event Message

Event Definition

Recommended Action

Auto Restart Fail

An Automatic Restart was enabled, but has

failed to complete.

With Automatic Restart enabled, the unit

automatically restarts after an End of Discharge

(EOD) event. This alarm means that one of the

auto restart requirements was true, but failed

before the restart sequence completed.

For example, one conditional requirement for

Automatic Restart to occur is that the Rectifier

Input Voltage must be within acceptable limits. If,

during the restart sequence, the input voltage

drops out of tolerance, the Automatic Restart will

fail.

This alarm is self-clearing. When the condition is

no longer present, the alarm and any control

activity tied to the alarm reverts to normal.

Press “SILENCE” to silence the audible alarm.

Check the active events to determine the status of

the UPS.

If “Auto Restart Fail” is the only alarm present,

attempt a manual start of the unit by pressing

“Startup,” “Manual Start,” then following the

prompts to attempt to place the unit back online.

If the manual start fails, or if there are other alarms

present that won’t clear, contact your factory-

authorized service provider.

Auto Rexfer

Failed

The condition that caused the system to

automatically disconnect the inverter from the

critical bus has failed to clear within a specified

time delay.

An example of a recoverable condition (one

which the controls may attempt to recover from

automatically) is an overload that exceeded the

overload capability.

Press “SILENCE” to silence the audible alarm.

Press “RESET” to attempt to clear active events.

This does not clear the “Auto Retransfer Failed”

alarm.

If all other alarm conditions are clear, for a single

module system attempt a manual transfer to

Inverter by pressing “Transfer,” “UPS.” For a multi-

module system attempt to manually reconnect this

inverter by pressing “Transfer,” “Connect This

Inverter.”

If successful, press “RESET” to clear this alarm

from the Active Event Window. If the UPS fails

connect the inverter to the critical bus and the

active messages do not explain the reason,

contact your factory-authorized service provider.

Bat Mon 1 Critical

Battery Monitor 1 is reporting a critical alarm.

Check the Battery Monitor Module for more details

on this condition.

Contact your factory-authorized service

representative for service.

Bat Mon 1 Maint

Battery Monitor 1 has an active Maintenance

Alarm.

Check the Battery Monitor Module for more details

on this condition.

Contact your factory-authorized service

representative for service.

Batt CB“#” Open

Battery Circuit Breaker “#” is open.

This status message is self-clearing. When the

condition is no longer present, the message and

any control activity tied to the status event

reverts to normal.

Press “SILENCE” to silence the audible alarm.

Check the status of Battery Circuit Breaker 1. If it is

open, the alarm is normal.

If Battery Circuit Breaker 1 is closed, contact your

factory-authorized service provider.

Содержание Liebert NXL 250 kVA

















































































































Результаты поиска

Содержание Liebert NXL 250 kVA

Отзывы:

Похожие инструкции для Liebert NXL 250 kVA

Бренды по названию

Популярные бренды

Emerson Liebert NXL 250 kVA, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Liebert NXL 250 kVA

Отзывы:

Похожие инструкции для Liebert NXL 250 kVA

Бренды по названию

Популярные бренды