Emerson Liebert NX Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 108

background image

Operating Instructions

75

9.4

Auto Restart

When the main and bypass sources fail, the UPS draws power from the battery system to supply the

load until the batteries are depleted. When the UPS reaches its end of discharge (EOD) threshold, it

will shut down.
The UPS will automatically restart and enable output power:

• after utility power is restored
• if “Auto Recovery after EOD Enabling” is enabled
• after the “Auto Recovery after EOD Delay Time” expires (the default delay is 10 minutes)

During the auto recovery delay, the Liebert NX will be charging its batteries to provide a safety

margin for equipment shutdown if input power fails again.

If the “Auto Recovery after EOD Enabling” feature is disabled, the user must restart the system man-

ually.

9.5

Emergency Shutdown With EPO

This circuit has been designed to switch off the UPS in emergency conditions (i.e., fire, flood, etc.). The

system will turn off the rectifier and inverter and will stop powering the load immediately (including

the inverter and bypass), and the battery stops charging or discharging. If a Liebert NX battery cabi-

net is connected, the circuit breaker in the battery cabinet will shunt trip open.
If input utility power is present, the UPS’s controls will remain active; however, the output will be

turned off. To remove all power from the UPS, open the external feeder breaker.

9.6

Reset After Shutdown for Emergency Stop (EPO Action) or Other Conditions

Once all appropriate measures have been taken to correct the problem indicated by the alarm mes-

sage appearing on the operator control panel display, carry out this procedure to restore the UPS to

regular operation following an EPO action or for the following reasons: Inverter Overtemperature,

Cut-off Overload, Battery Overvoltage, excessive switching (BYP: XFER COUNT BLOCK), etc.
When the user confirms that the fault is cleared:
1. Press the FAULT CLEAR button to let the system exit the emergency-off state.

2. Press the INVERTER ON button on the right side of the operator control panel for longer than

2 seconds.

After the EPO button is pressed, if the input utility is removed, the UPS will shut down completely.

When input utility is returned, if the Bypass input circuit breaker (CB2) and UPS output circuit

breaker (CB5) are closed, the UPS will start up on Bypass. There will be power at the output termi-

nals of the UPS.

NOTE

The rectifier will start again, and the bypass will begin to power the load. The Rectifier

indicator flashes while the rectifier is starting up. When the rectifier enters the normal

operation state (about 30 seconds), the rectifier indicator turns green.

NOTE

The rectifier will automatically turn on 5 minutes after the Inverter Overtemp alarm has

cleared.

!

WARNING

If the internal maintenance bypass circuit breaker (CB3) is closed and input utility is present,

there will be power at the output terminals of the UPS.

«
...
81
82
83
84
85
...
»

Содержание Liebert NX













































































































Отзывы:

Нет отзывов

Похожие инструкции для Liebert NX

Minuteman Encompass EC1000RT2U

Бренд: Para systems Страницы: 16

Бренд: Xtreme Power Conversion Страницы: 86

Бренд: Galleon Страницы: 22

Rugged-UPS 2500 Series

Бренд: Acumentrics Страницы: 33

Бренд: Avaya Страницы: 76

jupiter pro series

Бренд: Vision Страницы: 12

Бренд: Riello UPS Страницы: 24

Master HE 100 kVA

Бренд: Riello UPS Страницы: 34

Бренд: Eaton Страницы: 23

Бренд: Eaton Страницы: 22

Бренд: Tripp Lite Страницы: 28

Бренд: Tripp Lite Страницы: 48

Бренд: Tripp Lite Страницы: 56

INGENIO COMPACT

Бренд: Borri Страницы: 48

Бренд: LESTAR Страницы: 2

Бренд: Xmart Страницы: 41

Бренд: Eaton Страницы: 20

Evolution 650/650 Rack 1UEvolution 850

Бренд: Eaton Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды