Emerson Liebert APM 120 Скачать руководство пользователя страница 59

Страница: 59 / 144

Battery Installation

Liebert

APM

™

5.4

External Battery Cabinet Installation

5.4.1 Matching Battery Cabinets

A matching battery cabinet is available. Refer to

Figure 37

. The same model battery cabinet may be

installed in parallel in multiple cabinet strings for additional capacity. Battery run time depends on

the cabinet model, the number of cabinets and the load on the UPS.

Handling

—The battery cabinet has casters to facilitate movement over short distances. The bottoms

of the battery cabinets are reinforced to permit movement by forklift over longer distances.

Inspection

—Remove all panels and visually inspect the batteries, bus connections, and cabinet for

any damage. Exercise caution; voltage is present within the battery cabinet even before installation.

If there are signs of damage, do not proceed. Call Liebert Services at 1-800-542-2378.

Storage

—The batteries can be stored for up to six months without appreciable deterioration. If

planning to store a battery cabinet for longer than six months or at temperatures higher than 77°F

(25°C), contact Liebert Services for recommended precautions.
The following notes, in conjunction with the diagrams (

Figure 37

), illustrate the broad principles to

be followed when fitting and connecting the majority of battery cabinet installations.

When installing an external battery cabinet that is NOT a Liebert APM battery cabinet, the customer

must provide overcurrent protection. See

Table 43

for sizing of protection devices.

Figure 36 Bolting the battery cabinet to the Liebert APM

CAUTION

Any battery system should be installed by properly trained and qualified personnel.

NOTE

When using an external battery supply that is not provided with the UPS, please make

reference to the battery manufacturer’s installation manual for battery installation and

maintenance instructions, available on the manufacturer’s Web site. When replacing batteries,

Emerson recommends that the batteries in external cabinets be the same type used internally in

the Liebert APM. See

Tables 38

and

for batteries that are approved for use with the Liebert

APM.

DETAIL B

Liebert

APM

Battery

Cabinet

Washer
Split, M10

Hex Head
Bolt, M10

Содержание Liebert APM 120

















































































































































Результаты поиска

Содержание Liebert APM 120

Отзывы:

Похожие инструкции для Liebert APM 120

Бренды по названию

Популярные бренды

Emerson Liebert APM 120, Руководство пользователя

Результаты поиска

Содержание Liebert APM 120

Отзывы:

Похожие инструкции для Liebert APM 120

Бренды по названию

Популярные бренды