Emerson Liebert APM 120 Скачать руководство пользователя страница 128

Страница: 128 / 144

Specifications and Technical Data

Liebert

APM

™

118

11.4 UPS Electrical Characteristics

Refer to additional circuit breaker notes in

3.2.8 - Accessory Fuses and Backfeed Breaker

Wiring

NOTE

The breakers and cables used must be in accordance with NEC ANSI/NFPA 70. A disconnect

breaker must be provided for AC input, DC input and AC output. Recommended cable sizes are

suitable for operation at a maximum temperature of 86°F (30°C). For continuous operation at

temperatures above 86°F (30°C), the site design should include cables that meet requirements

for 104°F (40°C) installations.

Table 41

UPS currents and terminals—Input (for single-input unit, 208V operation)

Unit

Rating

Nominal

Input

Current

Maximum

Input

Current

OCP

Device

Rating

Bolt Size

Maximum Recommended Lug (T&B)

75°C Wire

Current, tot

Wire

Compression

Lug Two Hole

3/8" Bolt

Mechanical

Lug Two Hole

3/8" Bolt

M10 (3/8")

130

(1) #1

54857BE

32209

112

125

M10 (3/8")

150

(1) 1/0

54860BE

32209

134

167

200

M10 (3/8")

200

(1) 3/0

54864BE

32211

179

223

250

M10 (3/8")

300

(2) 1/0

54860BE

32209

224

279

350

M10 (3/8")

350

(2) 2/0

54862BE

32209

268

334

400

M10 (3/8")

460

(2) 4/0

54866BE

32211

Table 42

UPS currents and terminals—Input (for dual-input unit only, 208V operation)

Unit

Rating

Nominal

Input

Current

Maximum

Input

Current

OCP

Device

Rating

Bolt Size

Maximum Recommended Lug (T&B)

75°C Wire

Current, tot

Wire

Compression

Lug Two Hole

3/8" Bolt

Mechanical

Lug Two Hole

3/8" Bolt

M10 (3/8")

130

(1) #1

54857BE

32209

112

125

M10 (3/8")

150

(1) 1/0

54860BE

32209

134

167

200

M10 (3/8")

200

(1) 3/0

54864BE

32211

179

223

250

M10 (3/8")

300

(2) 1/0

54860BE

32209

224

279

350

M10 (3/8")

350

(2) 2/0

54862BE

32209

268

334

400

M10 (3/8")

460

(2) 4/0

54866BE

32211

Table 43

UPS currents and terminals—Bypass input (for dual-input units, 208V operation)

Unit

Rating

Nominal

Input

Current

OCP Device

Rating

Bolt Size

75°C Wire

Current, tot

Wire

Maximum Recommended Lug (T&B)

Compression

Lug Two Hole

3/8" Bolt

Mechanical

Lug Two Hole

3/8" Bolt

M10 (3/8")

130

(1) #1

54857BE

32209

110

M10 (3/8")

150

(1) 1/0

54860BE

32209

126

175

M10 (3/8")

175

(1) 2/0

54862BE

32209

168

225

M10 (3/8")

230

(1) 4/0

54866BE

32211

210

300

M10 (3/8")

300

(2) 1/0

54860BE

32209

252

350

M10 (3/8")

350

(2) 2/0

54862BE

32209

Содержание Liebert APM 120

















































































































































Результаты поиска

Содержание Liebert APM 120

Отзывы:

Похожие инструкции для Liebert APM 120

Бренды по названию

Популярные бренды

Emerson Liebert APM 120, Руководство пользователя

Результаты поиска

Содержание Liebert APM 120

Отзывы:

Похожие инструкции для Liebert APM 120

Бренды по названию

Популярные бренды