Emerson Liebert APM 120 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 144

background image

Electrical Connections—UPS

Liebert

®

APM

™

32

Common Input Connections

5. For common bypass and main inputs, connect the AC input supply cables to the UPS input

terminals (A2-B2-C2-N1) and tighten the connections to 240lb-in. (27N-m) (M10 Bolt). Ensure

correct phase rotation.

Split Bypass Connections

6. If a split bypass configuration is used, connect the AC input supply cables to the rectifier input

terminals (A1-B1-C1-N1) and the AC bypass supply cables to the bypass input terminals

(A2-B2-C2-N1) and tighten the connections to 240lb-in. (27N-m) (M10 Bolt). Ensure correct phase

rotation.

Output System Connections—Ensure Correct Phase Rotation

7. Connect the system output cables between the UPS output busbars (A-B-C-N terminals) and the

critical load and tighten the connections to 240lb-in. (27N-m) (M10 bolt).

Internal UPS Battery Connections

The UPS internal batteries will be connected at the factory, EXCEPT the connections between the

shelves and to the breaker.

Observe the battery cable polarity.

Be sure that the battery connection is made with the cor-

rect polarity.

8. Refit all protective covers removed for cable installation.

3.3

Control Cables Details

3.3.1 Static Bypass Assembly Features

Based on your site’s specific needs, the UPS may require auxiliary connections to manage the battery

system (external battery circuit breaker, battery temperature sensor), communicate with a personal

computer or provide alarm signaling to external devices or for Remote Emergency Power Off (REPO).

Terminations for these functions are located at the front of the static bypass module. The main

features are:

• Input and output dry contacts signal (one pair of contacts of relay)
• Emergency Power Off control (EPO)
• Environmental parameter input interface
• User communication (for data setting and user background monitor)
• Liebert IntelliSlot

®

interface

• Temperature detect interface

NOTE

For common bypass and main inputs, the AC input cables must be connected to the bypass

terminal (A2-B2-C2-N1) but not the main input terminal (A2-B2-C2).

NOTE

For split bypass operation, ensure that the busbars between bypass and rectifier inputs are

removed. The neutral line of the bypass input must be connected to that of the rectifier input.

!

WARNING

Risk of electrical shock and arc flash. Can cause property damage, injury and death.
If the load equipment will not be ready to accept power when the commissioning engineer

arrives, ensure that the system output cables are safely isolated.

!

WARNING

Risk of electrical shock and arc flash. Can cause property damage, injury and death.
The DC bus is live when this internal battery connection is made. This connection is to be

performed ONLY by Emerson Network Power

®

Liebert Services at startup.

«
...
40
41
42
43
44
...
»

Содержание Liebert APM 120

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Liebert APM 120

Бренд: Ewent Страницы: 61

Бренд: Tripp Lite Страницы: 5

Бренд: CyberPower Страницы: 2

Sentinel Dual SDU 4000

Бренд: Riello UPS Страницы: 36

SENTINEL POWER GREEN Series

Бренд: Riello UPS Страницы: 41

CSS SENTINEL TOWER CAM 3

Бренд: Riello UPS Страницы: 40

Sentinel RT 10000 VA ER

Бренд: Riello UPS Страницы: 42

Бренд: Riello UPS Страницы: 44

MASTER HP-UL 100-00

Бренд: Riello UPS Страницы: 83

Бренд: Tuncmatik Страницы: 35

Бренд: PowerWalker Страницы: 4

Бренд: PowerWalker Страницы: 14

Бренд: PowerWalker Страницы: 14

Бренд: PowerWalker Страницы: 38

Бренд: HELIOR Страницы: 26

Stabilizer Series SS10000

Бренд: OPTI-UPS Страницы: 1

Бренд: Sola HD Страницы: 16

Бренд: Sola HD Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды