Emerson Liebert APM 120 Скачать руководство пользователя страница 24

Страница: 24 / 144

Installation

Liebert

APM

™

2.8

Liebert FlexPower

™

Assembly

Figure 2

Liebert FlexPower assembly indicators and controls

The Battery start button allows starting of UPS on battery; refer to

10.3 - UPS Battery Start

The Run LED is illuminated Green when the Liebert FlexPower assembly is operating normally.
The Fault LED will illuminate red when the Liebert FlexPower assembly has a problem.

2.9

Static Bypass Assembly

Figure 3

Static bypass assembly connections

The Static bypass assembly has three Liebert IntelliSlot interface card bays and connections for

ancillary cabinets (Liebert BDC and battery) and for options.

Table 3

LED indications

LED Status

Indication

Run LED (Green)

Flashing Green

The inverter is starting, but has no output yet.

Constant Green

The inverter has started to supply power.

OFF

The inverter has not started up.

Fault LED (Red)

Constant Red

Auxiliary power failure (15V or 24V), rectifier overtemperature, rectifier failure (including battery

SCR short circuit), battery converter failure, soft start failure, main circuit back feed, abnormal

input current, inverter failure, output short circuit, bypass SCR short circuit fault, inverter relay

short circuit fault, abnormal bus voltage under non-sleep mode, module not ready, module ID

out of range and duplicated module ID.

Flashing Red

Charger failure, abnormal main circuit voltage, abnormal main circuit frequency, main circuit

undervoltage, main circuit reverse phase, battery unavailable, reverse battery, input zero-loss,

current sharing failure, module overload, inverter relay disconnection fault, bypass SCR

disconnection fault and input fuse blown.

OFF

No above failures or alarms.

Run LED

Battery Start Button

Ready Switch

Fault LED

DIP Switches

Input/output dry contact and EPO/BCB/MBC interface

J10

MFP_O

MFP_S

MFP_C

J11

INPUT_2

INPUT_1

OUT

GND

+12V

-IN

-OUT

GND

PARA

BCB_IN

DRIVER

GND

ONLINE

Q2BP

Q3BP

EXT

-OUT

GND

PARA

BFP_O

BFP_S

BFP_C

J12

INV_O

INV_S

INV_C

T_GND

ENV_DET

T_READY

+12V

EPO-NC

+12V

EPO-NO

LBS

MONITOR

RS485-2

RS485-1

RS232

INTELLISLOT3

INTELLISLOT2

INTELLISLOT1

J1 ~ J3 port can’t connect to phone!

J10

RS-232

Liebert IntelliSlot

Bays 1, 2, 3

RS-485

J11

J12

Monitor

Содержание Liebert APM 120

















































































































































Результаты поиска

Содержание Liebert APM 120

Отзывы:

Похожие инструкции для Liebert APM 120

Бренды по названию

Популярные бренды

Emerson Liebert APM 120, Руководство пользователя

Результаты поиска

Содержание Liebert APM 120

Отзывы:

Похожие инструкции для Liebert APM 120

Бренды по названию

Популярные бренды