Emerson Level-Trol 2500 Скачать руководство пользователя страница 28

Страница: 28 / 32

Type 2500

Instruction Manual

Form 1013

December 2005

Figure 15. Bourdon Tube-Flapper Arrangements for Various Actions and Mountings

AC9554

AR8148

BO996

−

1/IL

0.2 to 1 bar or 0 to 1.4 bar (3 to 15 psig or 0 to 20

psig) range. Use a tube with a red color code for a

0.4 to 2 bar or 0 to 2.4 bar (6 to 30 psig or 0 to 35

psig) range. The range is stamped at the Bourdon

tube base.

4. Mount the Bourdon tube on the level set arm (key

28). Secure it with the mounting screws, using the

proper orientation as shown in figure 15. Connect

the tubing to the tube base, with tubing from the R

connection on the relay (key 34) going to the marked

base connection. The other tubing goes to the

unmarked base connection. With an indicator

assembly, install the pointer assembly on the rotary

shaft and tighten the hex nut.

5. Perform the calibration procedure.

Changing Action

Note

The following procedure is necessary

to restore previous action if the

mounting method has been changed.

Figure 16 shows key numbers.

1. Reposition the Bourdon tube (and indicator

assembly, if used) according to steps 1 through 4 of

the Replacing the Bourdon Tube section.
2. Loosen the hex nut (key 40) and remove the

flapper base (key 30) from the torque tube rotary

shaft. Turn the flapper base over and install it on the

rotary shaft, using the proper orientation as shown in

figure 15 and making sure the flapper is centered

over the nozzle or Bourdon tube valve.
3. Perform the calibration procedure.

Содержание Level-Trol 2500

































Результаты поиска

Содержание Level-Trol 2500

Отзывы:

Бренды по названию

Популярные бренды

Emerson Level-Trol 2500, Инструкция по эксплуатации

Результаты поиска

Содержание Level-Trol 2500

Отзывы:

Бренды по названию

Популярные бренды