Emerson LDF42 Скачать руководство пользователя страница 18

Страница: 18 / 21

Chapter 4 Maintenance And Troubleshooting 15

Fan speed controller board
Bolt 2

Bolt 1

散热片

Heat sink

Figure 4-2 Removing the fan speed controller board

4.2 Troubleshooting

See Table 4-1 for alarm troubleshooting.

Table 4-1 Table of alarm troubleshooting

Alarm

number ID

Alarm name

Cause

Troubleshooting

One phase or two phases of three-phase
voltage are lost

Check that the three-phase voltage is correct

The input connection is reversed

Check the input order of wire

A00

Phase loss
alarm

The fan speed controller board has a
hardware fault

Replace the fan speed controller board and compare
the result of two boards

The fan cannot run normally

Check that the fan runs normally

A01

SCR over
temperature

The fan speed controller board has a
hardware fault

Replace the fan speed controller board and compare
the result of two boards

The fan cannot run normally

Check that the fan runs normally

The AC contactor supplying power for fan
has fault or its wire cuts off

Check the wiring of AC contactor; detect the auxiliary
contact state of AC contactor

A02, A03

Fan 1 over
temperature,
Fan 2 over
temperature

The fan speed controller board has a
hardware fault (the detecting circuit or SCR
power supplying circuit has fault)

Replace the fan speed controller board and compare
the result of two boards

The pressure sensor is not installed or its
terminal connection is poor

Check the wiring of pressure sensor

Jumper caps are not used to short terminals
J17 and J18 of current pressure sensor

Install the jumper cap when the current pressure
sensor is configured

Pressure sensor failed

Replace the pressure sensor and compare the result
of two boards

A04

Pressure
sensor failure

The fan speed controller board has a
hardware fault

Replace the fan speed controller board and compare
the result of two boards

A05

EEPROM
read fault

The fan speed controller board has a
hardware fault

Replace the fan speed controller board and compare
the result of two boards

The SCR temperature sensor is not
installed or its terminal connection is poor

Check the wiring of SCR temperature sensors (J8
SCRTemp, see Figure 3-1 for its position )

SCR temperature sensor failed

Replace the SCR temperature sensor and compare
the result of two sensors

A06

SCR
temperature
sensor failure

The fan speed controller has a hardware
fault

Replace the fan speed controller board and compare
the result of two boards

A07

Abnormal
frequency

The frequency of power supply voltage is
wrong
The fan speed controller has a hardware
fault

Replace the fan speed controller board and compare
the result of two boards

Liebert.PEX Condenser User Manual

Содержание LDF42






















Результаты поиска

Содержание LDF42

Отзывы:

Похожие инструкции для LDF42

Бренды по названию

Популярные бренды

Emerson LDF42, Руководство пользователя

Результаты поиска

Содержание LDF42

Отзывы:

Похожие инструкции для LDF42

Бренды по названию

Популярные бренды