manualshive.com logo in svg

Emerson KEYSTONE OM13 EPI-2, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Emerson KEYSTONE OM13 EPI-2 Скачать руководство пользователя страница 5

Installation, Operation and Maintenance Manual

VCIOM-01495-EN Rev. 1

May 2022

1

Optional Module 13: 3-Wires  Module

Section 1: Optional Module 13: 3-Wires Module

NOTE:

Before installation, these instructions must be fully read and understood.

Section 1: Optional Module 13:  

3-Wires Module

1.1 

OM13 Module Functionality

The OM13 3-wires module is supplied as an option to the Keystone EPI2 actuators. It is 
possible to receive the actuator already equipped with the OM13, ordering it with the 
basic feature. Alternatively, it is possible to order the OM13 as a separate kit and install 
it in the basic actuator in the factory or in the field. The OM13 is an optional module 
suitable to accomplish the following EPI2 actuator additional functionality:

• 

120/240 V AC 1-phase, 50/60 Hz, 3-wire control for open/close operations, 
without additional power supply.

 NOTE:

For decommissioning instructions, please refer to the relevant section in the EPI2 
VCIOM-15516-EN.

NOTE:

The OM13 command has to be provided by two separate switches for open and for close 
with a delay of at least one second between the two commands, when reversing the 
operation from open to close or vice versa.

! 

WARNING

EPI2 actuator must be electrically isolated before any disassembling or reassembling 
operations. Before any disassembling or reassembling operations, please follow in 
detail the relevant paragraph of the basic installation and operating manual (latest 
revision available).

! 

WARNING

The electronic parts of the EPI2 actuators and all option modules can be damaged by 
a discharge of static electricity. Before you start, touch a grounded metal surface to 
discharge any static electricity.

Содержание KEYSTONE OM13 EPI-2





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды