Emerson HIGH COUNTRY KF160OI01 Скачать руководство пользователя страница 14

Страница: 14 / 16

Trouble Shooting

TROUBLE

PROBABLE CAUSE

SUGGESTED REMEDY

1. Fan will not

1. Fuse or circuit breaker

1. Check main and branch

start.

blown.

circuit fuses or circuit breakers.

2. Loose power line connections

2. Check line power connections

to the fan, or loose switch wire

to fan and switch wire

connections in the switch

housing.

3. Wall switch is off.

3. Turn on wall switch.

4. Defective battery in remote

4. Check that the battery is good

control transmitter.

(red indicator light should
illuminate when any button is
pressed).

5. Code switches in remote

5. Check that both code switches

control receiver and transmitter

are set in the same positions.

are not set in the same position.

WARNING:

Make sure

main power is turned off.

2. Fan sounds

1. Blades not attached to fan.

1. Attach blades to fan before

noisy.

operating.

2. Screws securing fan blade

2. Check to make sure the screws

flanges to motor are loose.

which attach the blade flanges
to the motor are tight.

3. Wire connectors inside switch

3. Check to make sure wire

housing rattling.

connectors in switch housing
are not rattling against each
other or against the interior wall
of the switch housing.

WARNING:

Make sure main

power is turned off.

4. Screws holding blades to

4. Tighten screws securely.

flanges are loose.

5. Loose screws in motor housing. 5. Check to make sure all screws

in motor housing are snug
(not over-tight)

3. Fan wobbles

1. Setscrew in motor coupling is

1. Raise coupling cover and tighten

excessively.

not tightened securely.

setscrew securely.

2. Setscrew in the hanger ball/

2. Tighten the setscrew in the

downrod assembly is loose.

hanger ball/downrod assembly.

3. Screws securing fan blade

3. Check to be sure screws which

flanges to motor are loose.

attach the fan blade flanges
to the motor are tight.

4. Fan blade flanges not seated

4. Check to be sure that the

properly.

screws securing the fan
blade flanges seat firmly.

5. Hanger bracket and/or ceiling

5. Tighten the hanger bracket

outlet box is not securely

screws to the outlet box, and/or

fastened.

secure outlet box.

6. Fan blades out of balance.

6. Interchanging an adjacent (side

by-side) blade pair can
redistribute the weight and result
in smoother operation.
Or use supplied balancing kit to
balance blades.

WARNING:

FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX

OR CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN.

BP7283, High Country, KF160 7/31/06 10:54 AM Page 14

Содержание HIGH COUNTRY KF160OI01

















Результаты поиска

Содержание HIGH COUNTRY KF160OI01

Отзывы:

Похожие инструкции для HIGH COUNTRY KF160OI01

Бренды по названию

Популярные бренды

Emerson HIGH COUNTRY KF160OI01, Руководство пользователя

Результаты поиска

Содержание HIGH COUNTRY KF160OI01

Отзывы:

Похожие инструкции для HIGH COUNTRY KF160OI01

Бренды по названию

Популярные бренды