background image

3. Screw the two threaded studs (supplied) into the

tapped holes in the hanger bracket.

4. Lift the ceiling cover up to the threaded studs and

turn until studs protrude through the holes in the
ceiling cover (Figure 10).

5. Secure the ceiling cover in place by sliding lock-

washers over the threaded studs and installing the
two knurled knobs (supplied). (Figure 10). Tighten
the knurled knobs securely until the ceiling cover fits
snugly against the ceiling and the hole in the ceiling
cover is clear of the downrod. Your fan is now wired
to be turned on and off from the fan switch.

6. Cut the 3-speed switch pull chain to a desired

length (optional). Connect the wood pendant (sup-
plied) to the 3-speed switch pull chain by sliding the
wooden pendant (small hole first) onto the pull
chain. Attach the chain coupler to the end of the
chain and allow the wooden pendant to fall down
over the coupling.

If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.

1. Connect the green grounding lead from the hanger

ball and the green grounding lead from the hanger
bracket to the grounding conductor of supply (this
may be a bare wire or wire with green colored insu-
lation). Securely connect wires with wire connec-
tors supplied.

NOTE: If you are using an Emerson Light Fixture
with your fan, see Light Fixture Owner’s Manual
for wiring.

2. Securely connect the fan motor white wire to the

supply white (neutral) wire using wire connector
supplied (Figure 9). Securely connect the fan motor
black wire and blue wire to the supply black (hot)
wire using wire connector supplied (Figure 9). After
connections have been made, turn leads upward
and carefully push leads into the outlet box, with
the white and green leads on one side of the outlet
box and the black and blue leads on the other side
of the outlet box.

6

How to Wire

Your Ceiling Fan

NOTE: CEILING COVER
OMITTED FOR CLARITY.

GROUND
WIRE

LISTED
WIRE
CONNECTOR (3)

GREEN WIRE
(GROUND) FROM
HANGER BRACKET

GREEN WIRE
(GROUND) FROM
HANGER BALL

WHITE SUPPLY
(NEUTRAL)

WHITE FAN
WIRE

BLACK SUPPLY
(HOT)

BLACK AND BLUE
FAN WIRES

Figure 4

CEILING COVER

THREADED
STUD

KNURLED KNOB

LOCKWASHERS (2)

Using Your Ceiling Fan

Figure 9

Figure 10

1. Restore electrical power to the outlet box by turning

the electricity on at the main fuse box.

2. Check the operation of the fan by gently pulling on

the pull chain switch.

3. All fans are shipped from the factory with the

reversing switch positioned to circulate air down-
ward. If airflow is desired in opposite direction, turn
your fan off and wait for the blades to stop turning,
then slide the reversing switch to opposite position,
and turn fan on again. The fan blades will turn in
the opposite direction and reverse the airflow.
Your fan model is equipped with a 4-position,
3-speed pull chain switch. The operating sequence
is as follows:

THREE-SPEED
1st Pull—HIGH
2nd Pull—Medium
3rd Pull—Low
4th Pull—OFF

SPEED
CONTROL
SWITCH

REVERSING
SWITCH

OUTLET
BOX

HANGER
BRACKET

HANGER BALL/
DOWNROD ASSEMBLY

SUPPLY WIRES AND
FAN WIRES OMITTED
FOR CLARITY.

Figure 8

To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and
hanger bracket.

WARNING

!

NOTE: CEILING COVER,
SUPPLY WIRES AND FAN
WIRES OMITTED FOR
CLARITY.

To avoid possible electrical shock, be sure electricity
is turned off at the main fuse box before wiring.
NOTE: If you are not sure if the outlet box is ground-
ed, contact a licensed electrician for advice, as it
must be grounded for safe operation.

WARNING

!

Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until blades are in place. Noise and fan
damage could result.

WARNING

!

To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box and
not pinched between the ceiling cover and the ceiling.

WARNING

!

Содержание HARDWOOD CF796CW0









Отзывы: