manualshive.com logo in svg

Emerson Fisher YD, Инструкция по эксплуатации

Поделиться
Скачать
Emerson Fisher YD Скачать руководство пользователя страница 24

Instruction Manual

D100425X012

YD and YS Valves

July 2017

24

Parts Ordering

Each valve is assigned a serial number which can be found on the valve. This same number also appears on the
actuator nameplate when the valve is shipped from the factory as part of a control valve assembly. Always refer to the
serial number when corresponding with your 

Emerson sales office

 or Local Business Partner about this equipment.

When ordering replacement parts, also state the complete eleven‐character part number for each part required from
the following parts list.

  WARNING

Use only genuine Fisher replacement parts. Components that are not supplied by Emerson Automation Solutions should
not, under any circumstances, be used in any Fisher valve, because they may void your warranty, might adversely affect the
performance of the valve, and could cause personal injury and property damage.

Parts Kits

Standard Packing Repair Kits (Non Live‐Loaded)

Stem Diameter, mm (Inches)

Yoke Boss Diameter, mm (Inches)

9.5 (3/8)

54 (2‐1/8)

12.7 (1/2)

71 (2‐13/16)

19.1 (3/4)

90 (3‐9/16)

25.4 (1)

127 (5)

PTFE (Contains keys 6, 8, 10, 11, and 12)

RPACKX00012

RPACKX00022

RPACKX00032

RPACKX00342

Double PTFE (Contains keys 6, 8, 11, and 12)

RPACKX00042

RPACKX00052

RPACKX00062

RPACKX00362

PTFE/Composition (Contains keys 7, 8, 11, and 12)

RPACKX00072

RPACKX00082

RPACKX00092

- - -

Single Graphite Ribbon/Filament (Contains keys 7 [ribbon ring], 
7 [filament ring], 8, and 11)

RPACKX00102

RPACKX00112

RPACKX00122

- - -

Single Graphite Ribbon/Filament (Contains keys 7 [ribbon ring], 
7 [filament ring], and 11)

- - -

- - -

- - -

RPACKX00532

Single Graphite Ribbon/Filament (Contains keys 7 [ribbon ring], 
7 [filament ring])

RPACKX00132

RPACKX00142

RPACKX00152

- - -

Double Graphite Ribbon/Filament (Contains keys 7 [ribbon ring], 
7 [filament ring], 8, and 11)

RPACKX00162

RPACKX00172

RPACKX00182

- - -

Packing Kits (ENVIRO‐SEAL) Repair

PACKING

MATERIAL

STEM DIAMETER AND YOKE BOSS DIAMETER, mm (INCH)

9.5 (3/8)

54 (2‐1/8)

12.7 (1/2)

71 (2‐13/16)

19.1 (3/4)

90 (3‐9/16)

25.4 (1)

127 (5)

Double PTFE (contains keys 214, 215, & 218)

RPACKX00192

RPACKX00202

RPACKX00212

RPACKX00222

Graphite ULF (contains keys 207, 208, 209, 210, and 214)

RPACKX00592

RPACKX00602

RPACKX00612

RPACKX00622

Packing Kits (ENVIRO‐SEAL) Retrofit

PACKING

MATERIAL

STEM DIAMETER AND YOKE BOSS DIAMETER, mm (INCH)

9.5 (3/8)

54 (2‐1/8)

12.7 (1/2)

71 (2‐13/16)

19.1 (3/4)

90 (3‐9/16)

25.4 (1)

127 (5)

Double PTFE (contains keys 200, 201, 211, 212, 214, 215, 217, and 218)

RPACKXRT012

RPACKXRT022

RPACKXRT032

RPACKXRT042

Graphite ULF (contains keys 200, 201, 207, 208, 209, 210,

211, 212, 214, and 217)

RPACKXRT262

RPACKXRT272

RPACKXRT282

RPACKXRT292

Содержание Fisher YD

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды