manualshive.com logo in svg

Emerson Fisher Level-Trol 2502 Series, Инструкция по эксплуатации, Страница: 23 / 28

Поделиться
Скачать
Emerson Fisher Level-Trol 2502 Series Скачать руководство пользователя страница 23

2502 Series Controllers

Instruction Manual

Form 1446

November 2006

23

Note

Beam overtravel can jam the flapper

against the nozzle if the following step

is not performed.

3.  Remove the flapper screw (key 93), lockwasher

(key 84), and flapper (key 60). Invert the flapper so

that the flapper hook is on the opposite side of the

beam from the nozzle (key 58), and secure with the

lockwasher and screw.
4.  Perform the calibration procedure and any other

necessary part of the calibration sequence.

Parts Ordering

Whenever corresponding with your Emerson

Process Management sales office about this

equipment, always mention the controller type

number and the serial number found on the unit

nameplate (figure 9). When ordering replacement

parts, also state the complete 11-character part

number of each required part as found in the

following parts list.

WARNING

Use only genuine Fisher

R

 replacement

parts. Components that are not

supplied by Emerson Process

Management should not, under any

circumstances, be used in any Fisher

instrument. Use of components not

supplied by Emerson Process

Management will void your warranty,

might adversely affect your the

performance of the instrument, and

might jeopardize worker and

workplace safety.

Note

Neither Emerson, Emerson Process

Management, Fisher, nor any of their

affiliated entities assumes

responsibility for the selection, use

and maintenance for any product.

Responsibility for the selection, use,

and maintenance of any product

remains with the purchaser and

end-user.

Parts Kits

Description

Part Number

Controller Parts Kit

Contains keys 12, 15, 21, 24, 38, 55, 57, 58, 60, 62, 63, 64,

77, 79, 84, 86, 87, 93, 101, and 187

Standard Temperature

R2502X00L52

High Temperature

R2502X00H52

Relay Replacement Kit

Contains keys 22, 43, and the relay assembly

Standard Temperature

RRELAYX0L22

High Temperature

RRELAYX0H22

Heat Insulator Parts Kit

Contains keys 35, 36, 37, 38, 39, 40, and 53

R2500XH0012

Parts List

Key

Description

Part Number

Heat Insulator (figure 12)

35

Heat Insulator Assembly, stainless steel

22A0033X012

36

Shaft Coupling, stainless steel

1A577935032

37

Shaft Extension, N05500

1B681540022

38

Set Screw, stainless steel (2 req’d)

1E6234X0022

39

Cap Screw, steel, pl (4 req’d)

1A381624052

40

Cap Screw, steel, pl (4 req’d)

1V239528982

53

Washer, carbon steel, pl (4 req’d)

1B865928982

Controller Common Parts (figure 14)

1

Pilot Case Back, zinc

Types 2502 and 2502C

1J415744012

Type 2502F

23A2073X012

2

Pilot Case Cover, aluminum

50B9454X012

3

Door Handle, steel, pl

1C897225082

4

Door Handle Shaft (not shown),

stainless steel

1C898414012

5

Machine Screw, stainless steel

1C8958X0022

6

Washer Spring, stainless steel

1C897036032

7

Door Hook, steel, pl

1C897125082

8

Elastic Stop Nut, steel, pl

1C8959X0012

9

Drive Pin, (2 req’d)

1C8991X0022

11

Relay Tubing, stainless steel 

17A9100X022

12* Ball Bearing Ass’y, brass, pl

1C8983000A2

13

Retaining Ring, steel, pl (2 req’d)

1A465828992

14* Gauge Glass, glass, (2 req’d)

0T019206042

15* Gauge Glass Gasket, chloroprene (2 req’d)

0T019104082

*Recommended spare parts

Содержание Fisher Level-Trol 2502 Series





























Отзывы:

Нет отзывов