Emerson Fisher Level-Trol 2502 Series Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 28

Emerson Fisher Level-Trol 2502 Series Скачать руководство пользователя страница 10

2502 Series Controllers

Instruction Manual

Form 1446

November 2006

10

RESET ADJUSTMENT

W5637/IL/A

29A2834-C

30A8943-H

A1933/IL

1E8731-C

1E8732-C

A1897-1/IL

21A6447-A

A1903/IL

INSTRUCTION LABEL

RAISE LEVEL DIAL FOR

LEFT-HAND MOUNTING

TYPE 2502C LEVEL INDICATOR

WITH RIGHT-HAND MOUNTING

POINTER ASSEMBLY

TYPICAL RIGHT-HAND MOUNTED

2502 SERIES CONTROLLER

DIFFERENTIAL RELIEF VALVE

ON BACK OF TYPE 2502 CASE

TRAVEL INDICATOR PLATE

FOR LEFT HAND MOUNTING

MOUNTING

SCREWS

ADJUSTING

SCREW

Figure 9. Controller Adjustments

1. Turn on the supply pressure and check that the

controller supply gauge reads 1.4 bar (20 psig) for

a 0.2 to 1.0 bar (3 to 15 psig) output pressure range

or 2.4 bar (35 psig) for a 0.4 to 2.0 bar (6 to 30 psig)

output pressure range. If the pressure is incorrect,

loosen the locknut of the filter/regulator (figure 3);

turn the adjusting screw clockwise to increase or

counterclockwise to decrease pressure. Tighten the

locknut after setting the pressure.
2. Turn the reset control to .05 minutes per repeat.
3. Locate the process variable at its minimum value

(see table 2). Zero the proportional band and raise

level controls. Output pressure on direct-acting

controllers should be greater than zero but less

«
...
8
9
10
11
12
...
»

Содержание Fisher Level-Trol 2502 Series





























Отзывы:

Нет отзывов