manualshive.com logo in svg

Emerson Fisher EHD, Инструкция по эксплуатации

Поделиться
Скачать
Emerson Fisher EHD Скачать руководство пользователя страница 26

Instruction Manual

D100394X012

EH (1-1/2x1 through 8x6)

July 2017

26

seal contacts the cage, and inspect the sealing surface where the C‐seal plug seal makes contact with the plug
(figure 14).

9.  Replace or repair trim parts according to the following procedure for lapping metal seats, remachining metal seats,

or other valve plug maintenance procedures as appropriate.

Lapping Metal Seats (C‐seal Constructions)

Before installing a new C‐seal plug seal, lap the lower seating surface (valve plug to seat ring, figure 14) following
appropriate procedures in the Lapping Seats section of this manual.

Remachining Metal Seats (C‐seal Constructions)

See figure 15. A valve plug with a C‐seal metal plug seal features two seating surfaces. One seating surface is found
where the valve plug contacts the seat ring. The second seating surface is found where the C‐seal plug seal contacts
the upper seating surface in the cage. If you machine the seats on the seat ring and/or plug, you must machine an
equal dimension from the seating area in the cage.

Figure 14. Lower (Valve Plug to Seat Ring) and Upper (C‐seal Plug Seal to Cage) Seating Surfaces

NOTE:

        UPPER SEATING SURFACE IS THE AREA OF CONTACT BETWEEN THE C‐seal METAL PLUG SEAL AND THE CAGE.

PLUG

CAGE

SEAT
RING

LOWER SEATING SURFACE

A6780

1

C

-

seal METAL

PLUG SEAL

RETAINER

CAGE

VALVE PLUG

UPPER SEATING SURFACE

1

CAUTION

If metal is removed from the seat ring and plug and a corresponding amount is not removed from the cage seating area, the
C‐seal plug seal will be crushed as the valve closes and the C‐seal retainer will strike the seating area of the cage, preventing
the valve from closing.

Trim Replacement (C‐seal Constructions)

1.  Apply a suitable high‐temperature lubricant to the inside diameter of the C‐seal plug seal. Also, lubricate the

outside diameter of the valve plug where the C‐seal plug seal must be pressed into the proper sealing position
(figure 10).

2.  Orient the C‐seal plug seal for correct sealing action based on the process fluid flow direction through the valve.

D

 The open interior of the C‐seal plug seal must face up in a valve with flow‐up construction (figure 10).

D

 The open interior of the C‐seal plug seal must face down in a valve with flow‐down construction (figure 10).

Note

An installation tool must be used to properly position the C‐seal plug seal on the valve plug. A tool is available as a spare part from
your 

Emerson sales office

 or Local Business Partner or a tool could be manufactured following the dimensions given in figure 11.

Содержание Fisher EHD





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды