Emerson Fisher 3582 Скачать руководство пользователя страница 41

Страница: 41 / 56

Instruction Manual

D200138X012

3582, 582i, and 3583

January 2013

Parts List

Positioner/Transmitter Common
Parts (figure 21)

Note

Parts in the following list are common to both 3582 valve positioners
and 3583 position transmitters, unless identified by specific type
number.

Note

Part numbers are shown for recommended spares only. For part
numbers not shown, contact your Emerson Process Management sales
office.

Key

Description

Part Number

Case Assembly, Aluminum and PEEK

2* Shaft Assembly, SST/steel

For all except 3582NS and high vibration
For travel up to 54 mm (2.125 inch)

15A9609X012

For travel up to 102 mm (4 inch)

15A9609X022

For 3582NS and high vibration
For travel up to 54 mm (2.125 inch)

15A9609X102

For travel up to 102 mm (4 inch)

15A9609X112

Shaft Assembly, SST/steel
For 3582NS and high vibration
For travel up to 54 mm (2.125 inch)

Nozzle Adaptor, SST

Cam, SST
Cam A (For all types except 3582NS)
Cam B
(For all except 3582NS, 3583, 3583C)
Cam C
(For all except 3582NS, 3583, 3583C)

Cam, SST/nitride (for 3582NS and high vibration)
Cam A (for all types)
Cam B (For all except 3583, 3583C)
Cam C (For all except 3583, 3583C)

Cam Bolt, 416 SST

7* Bellows Assembly

Standard brass

13B8783X012

For sour gas

13B8783X022

Range Spring, pl steel (see table 9)
0.2 to 1.0 bar (3 to 15 psi)
0.4 to 2.0 bar (6 to 30 psi)

Spring Seat, aluminum

Machine Screw, pl steel

Key

Description

Part Number

11* O‐Ring

Std. const., Nitrile
All except 3582NS

1F463606992

Hi‐temp. const., Fluorocarbon
3582A, 3582C & 3583C

1N571406382

3582NS, EPDM Duro 80A

17B4784X012

Lockwasher, pl steel (2 req'd)

Machine Screw, pl steel (2 req'd)

Nozzle, SST
3582
3583

Flapper Sub‐Assembly

Note

Parts 19A through 19L are shown in figure 20.

19A Adjustment Arm, pl steel
19B Flapper, SST
19C Machine Screw, pl steel (2 req'd)
19D Flapper Arm, aluminum
19E

Machine Screw, pl steel (2 req'd)

19F

Flapper Spring, SST

19G Zero Adjustment Screw, 18‐8 SST/PEEK

19H Hex Nut, pl steel
19J

Lockwasher, pl steel

19K Arm Support, SST
19L

Pivot Pin, 440C SST

Setting Adjustment Gear,
All except 3582NS, nylon
3582NS, 316 SST

Figure 20. Flapper Sub‐Assembly (Key 19)

13A1451‐E

ASSEMBLE WITH LETTER
T ON THIS SURFACE

*Recommended spare parts

Содержание Fisher 3582

























































Результаты поиска

Содержание Fisher 3582

Отзывы:

Похожие инструкции для Fisher 3582

Бренды по названию

Популярные бренды

Emerson Fisher 3582, Инструкция по эксплуатации

Результаты поиска

Содержание Fisher 3582

Отзывы:

Похожие инструкции для Fisher 3582

Бренды по названию

Популярные бренды