background image

The SW116 wall control transmits the command
signals via radio waves to the SW105 receiver
installed in the ceiling fan ceiling cover. The
SW105 receiver is required for the SW116 wall
control to function. Power for the SW116 wall
control comes from the 12V battery, located in the
wall control.

Replacement 12V batteries recommended are
Duracell MN21, Eveready A23, and GP23A.

1.

Install the 12V battery (supplied) into the wall
control (Figure 22). 

2.

The SW116 wall control is supplied with a white,
ivory, or almond color cover. Choose the style that
best suits your needs and snap the cover onto the
wall control (Figure 22).

3.

Install the wall control onto the outlet box using the
supplied screws (Figure 23). 

4.

Install decorator wall plate (purchased separately)
using the two screws provided with wall plate.
Leave wall control in “OFF” mode until fan
installation is completed (Figure 23).

12V BATTERY

WALL
CONTROL
COVER

SW116 WALL
CONTROL

HI

HI

MED

MED

LOW

LOW

FAN  OFF

REV

REV

LIGHT

D/L

U/L

Setting Operating

Frequency of Wall Control

and Receiver 

(Figure 21)

Your wall control and receiver have code switches
which must be set in one of 16 possible code
combinations. The four levers (numbered 1, 2, 3, and
4) on the switches are factory-set in the ON (up)
position. Change the switch settings as follows:

1.

Slide the four switch levers in the wall control to
your choice of ON (up) or down positions. Use a
ball-point pen or small screwdriver and slide the
levers firmly up or down.

2.

In the receiver, slide the four switch levers to the
same positions as set in the wall control. Make
sure the levers on both switches are in the same
positions, otherwise the fan will not operate.

ON

1

2

3

4

RECEIVER SWITCH
LEVERS

ON

1

2

3

4

WALL CONTROL
LEVERS

CODE
SWITCH

SW105 RECEIVER

CODE
SWITCH

SW116 WALL 
CONTROL

HI

HI

MED

MED

LOW

LOW

FAN  OFF

REV

REV

LIGHT

Figure 21

Figure 22

SW116 WALL
CONTROL

DECORATIVE WALL PLATE
(Purchased Separately)

OUTLET BOX

WALL PLATE
SCREW (2)

WALL CONTROL
SCREW (2)

REV

HI

MED

LOW

FAN  OFF

U/L

D/L

LIGHT

Figure 23

Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse or circuit breaker box.

WARNING

!

Installation

of Wall Control

11

U.L. Model No.: CF3100

Содержание DUNNINGTON CF3100AGW00

















Отзывы: