Emerson daniel 1500 series Скачать руководство пользователя | Manualshive

Страница: 51 / 104

background image

4

Prepare the turbine meter for use

Topics covered in this chapter:

•

Lifting conditions

•

Lifting requirements for personnel

•

Configuration of the turbine meter

4.1

Lifting conditions

WARNING!

CRUSHING HAZARD

During turbine meter installation or removal, always place the unit on a stable platform or
surface that supports its assembled weight.

Failure to comply could allow the turbine meter to roll, resulting in death, serious injury or
equipment damage.

WARNING!

LIFTING HAZARD

The lifting instructions are for installation and removal of the Daniel Liquid Turbine Meter only
and do not address lifting the turbine meter while it is attached or bolted to piping.

Failure to comply with these instructions may result in death, serious injury, or equipment
damage.

CAUTION!

FORKLIFT HAZARD

Do not insert the forks of a forklift into the bore when moving the turbine meter.

Inserting the forks may cause the meter to become unstable, resulting in serious injury or
equipment damage.

Lifting and installation conditions

Table 4-1:

Conditions

Description

Lighting and ventilation

Install the turbine meter in a well lit and ventilated location, not
less than one meter (approximately three feet) from source of ig-
nition or source of heat which might damage the unit.

Prepare the turbine meter for use

User manual

41

«
...
49
50
51
52
53
...
»

Содержание daniel 1500 series









































































































Отзывы:

Нет отзывов

Похожие инструкции для daniel 1500 series

Бренд: Kane Страницы: 16

Бренд: Bacharach Страницы: 48

Бренд: Bacharach Страницы: 24

Бренд: Macnaught Страницы: 14

Бренд: Eaton Страницы: 43

Бренд: ICP DAS USA Страницы: 71

HYDROTECHNIK MultiHandy 2025

Бренд: ICS Страницы: 8

Бренд: ICT International Страницы: 24

Бренд: QMI Страницы: 54

Бренд: SAGEMCOM Страницы: 33

Бренд: Valhalla Scientific Страницы: 43

Бренд: Energic Plus Страницы: 12

Бренд: Keithley Страницы: 18

HYDROMETTE HB 30

Бренд: GANN Страницы: 65

Бренд: Dewetron Страницы: 48

Бренд: WIKA Страницы: 56

Бренд: AquaMetrix Страницы: 37

Бренд: Kawai Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды