Emerson Damcos Скачать руководство пользователя страница 56

Страница: 56 / 144

Service Manual

Damcos LPU: Troubleshooting Guide LPU

SM 8000-100-01 Ed 04

February 2017

Motor running hot, LPU is operating normally

Caution!

Motor is designed for 25% duty cycle only.

Action:

•

LPU-S
Observe that LPU does not restart.
If it is restarting frequently, the motor is running hot. See“LPU-S frequently restarting in open
position” on page 47.

•

Measure the supply voltage (220 - 230 V AC) to LPU.
If it differs widely from the required voltage, the voltage must be modified.

•

Measure the resistance over the motor windings, on the terminal (easiest with disconnected
capacitor). There must be approximately 15



between “N” and “OPEN” and “CLOSE” respec-

tively.
If this resistance is not observed, the motor is to be replaced.

•

The mechanical resistance of the motor can be too high.
If it cannot be turned easily with the fingers, it is to be replaced.

•

The mechanical resistance of the pump can be too high, if ball bearing is blocked.
Dismount valve block and pump rotor as to change pump (see “Replace Pump in LPU” on
page 93) and check if ball bearing can rotate freely.

Содержание Damcos

















































































































































Результаты поиска

Содержание Damcos

Отзывы:

Похожие инструкции для Damcos

Бренды по названию

Популярные бренды

Emerson Damcos, Руководство по обслуживанию

Результаты поиска

Содержание Damcos

Отзывы:

Похожие инструкции для Damcos

Бренды по названию

Популярные бренды