Emerson COPELAND ZO18AG Скачать руководство пользователя страница 37

Страница: 37 / 38

AGL_Ref_ST_ZO_E_Rev00

Appendix1: Tightening torques

Connection

Torque [Nm]

Rotalock 1"

20.3 - 33.9

Rotalock 1 ¼"

27.1 - 40.7

Sight glass external 1 ¼"

45.8 - 53.7

Sight glass fitting TPTL

34 - 41

Mounting bolts M8 (grommet for single operation)

13 ± 1

Mounting bolts M8 (hard mounting parts for //)

27 ± 1

Schraeder valve fitting 5/16, M9

4.5 - 6.8

Crankcase heater

2 - 3

Terminal block screw

1.4 - 1.7

IP54 box ground screw (Peko bolt)

3.6 - 4.4

IP54 ground screw cover / Tbox

3.6 - 4.4

IP54 cable gland M25

9.8 - 10

IP54 Tbox cover screws

1.0 - 1.2

DISCLAIMER

1. The contents of this publication are presented for informational purposes only and are not to be

construed as warranties or guarantees, express or implied, regarding the products or services
described herein or their use or applicability.

2. Emerson Climate Technologies GmbH and/or its affiliates (collectively "Emerson"), as

applicable, reserve the right to modify the design or specifications of such products at any time
without notice.

3. Emerson does not assume responsibility for the selection, use or maintenance of any product

Responsibility for proper selection, use and maintenance of any Emerson product remains solely
with the purchaser or end user.

4. Emerson does not assume responsibility for possible typographic errors contained in this

publication.

Содержание COPELAND ZO18AG







































Результаты поиска

Содержание COPELAND ZO18AG

Отзывы:

Похожие инструкции для COPELAND ZO18AG

Бренды по названию

Популярные бренды

Emerson COPELAND ZO18AG, Инструкции по применению

Результаты поиска

Содержание COPELAND ZO18AG

Отзывы:

Похожие инструкции для COPELAND ZO18AG

Бренды по названию

Популярные бренды