background image

 

AGL_Ref_ST_YFK1E_EN_Rev01 

 

About these  guidelines 

The  purpose of these guidelines is to provide guidance in the  application of Copeland

™ scroll 

compressors in users’ systems. They are intended to answer the questions raised while designing, 
assembling and operating a system with these products. 

Besides the support they provide, the instructions listed herein are also critical f or the proper and 
saf e functioning of the compressors. The performance and reliability of the product may be impacted 
if  the product is not used according to these guidelines or is misused. 

These  application guidelines cover stationary applications only. For mobile appl ications, please 
contact the Application Engineering department at Emerson as other considerations may apply. 

Safety instructions 

Copeland scroll compressors are manuf actured according to the latest relevant US and European 
saf ety standards. Particular emp

hasis has been placed on the user’s safety. 

YF*K1E compressors are  intended f or installation in systems in accordance with the  European 
Machinery Directive MD 2006/42/EC, the

 

Pressure Equipment Directive PED 2014/68/EU and the 

Low Voltage Directive LVD 2014/35/EU. They may be put to service only if they have been installed 
in systems according to 

the manufacturer’s instructions and conform to the corresponding provisions 

of  legislation. 

NOTE:  Only  dedicated compressors are  allowed to  be  used  with  flammable refrigerants. 
Emerson marks all compressors that are qualified for flammable refrigerants with a sticker 
indicating the usage  of  such  refrigerants. Systems using flammable refrigerants must be 
executed  correctly  while  observing  safety  rules,  as  specified  in  corresponding  safety 
standards such as, but not limited to EN 378. They must comply with any and all applicable 
legislation and regulations. Ensuring compliance remains the user’s responsibility. 

The Material Saf ety Datasheet (MSDS) of the individual refrigerant shall be considered when working 
with each type of refrigerant 

– please check the documentation provided by the refrigerant supplier. 

These instructions shall be retained throughout the lifetime of the compressor.  

You are strongly advised to follow these safety instructions. 

1.1  Icon explanation 

 

WARNING

 

This  icon  indicates  instructions  to 
avoid  personal  injury  and  material 
damage. 

 

Fire hazard

 

This icon indicates a risk of flammable 
atmosphere. 

 

High voltage

 

This  icon indicates operations with a 
danger of electric shock. 

 

CAUTION

 

This  icon  indicates  instructions  to 
avoid property damage and possible 
personal injury. 

 

Danger of burning or frostbite

 

This  icon indicates operations with a 
danger of burning or f rostbite. 

 

IMPORTANT

 

This  icon  indicates  instructions  to 
avoid malfunction of the compressor. 

 

Explosion hazard

 

This  icon indicates operations with a 
danger of explosion. 

NOTE 

 

This 

word 

indicates 

recommendation for easier operation. 

 

Danger of explosive atmosphere 

This icon indicates a risk of  explosive 
atmosphere. 

 

 

 
 

 

Содержание Copeland YF05K1E







































Отзывы: