manualshive.com logo in svg

Emerson CL1500, Инструкция по эксплуатации, Страница: 16 / 24

Поделиться
Скачать
Emerson CL1500 Скачать руководство пользователя страница 16

Instruction Manual

D104223X012

A11 Valve

August 2017

16

Seal Installation

For HPS seal installation:

 

Locate the replacement seal ring (key 8) and note the shape of the ring. The ring is wider across one edge diameter and
narrower across the other edge diameter as shown in figure 8. Around the outside circumference is one wide groove.

Install the seal ring (key 8) into the valve body by first placing the wider outside diameter of the seal ring into the T‐slot
area of the valve body which is shown in figure 9.

LARGEST OUTSIDE
DIAMETER (KEY 8)

A5251/IL

Figure 9. Typical Seal Installation

For Soft seal installation:

1.  Locate the replacement seal ring (key 8) and note the shape of the ring. The ring is wider across one edge diameter

and narrower across the other edge diameter as shown in figure 8. Around the outside circumference is one wide
groove.

Install the seal ring in the valve body by first placing the wider outside diameter of the seal ring, as marked in figure 8,
into the T‐slot area of the valve body which is shown in figure 9. Seal rings without a back‐up ring will fall into place.
The back‐up ring will have to be installed after placing the seal ring in the valve using a blunt end screwdriver. Do not
use the screwdriver or seal tool directly on the seal ring. Use a tool only on the backup ring.

2.  With the seal ring inserted all the way around the valve body T‐slot now lay the backup ring into the opening

between the valve body and the seal ring. Use the seal tool to apply pressure to the backup ring and carefully tuck
the backup ring down into the T‐slot between the valve body and the seal ring. Note: On larger valves, it may be
more efficient to have someone hold down the seal ring while the backup ring is pushed into the T‐slot.

3.  Once the seal ring or seal and backup ring has been fully installed into the valve body T‐slot, the retaining ring

gasket (key 17) can be installed.

Содержание CL1500

























Отзывы:

Нет отзывов