background image

10

How to Wire Your Ceiling Fan 

(continued)

STANDARD ON-OFF WALL 

SWITCH OR OPTIONAL SW406 

WALL CONTROL

BLACK

BLACK

WHITE

RED

BLACK

WHITE

HANGER BALL

GREEN WIRE (GROUND) 

FROM HANGER BALL AND 

HANGER BRACKET

TWO-CONDUCTOR 

CABLE (WITH 

GROUND)

BLACK 

(HOT)

WHITE

GROUND

TO

120-

VOLT

SUPPLY

WHITE

BLUE

WHITE

BLUE

Figure 15

To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box
and not pinched between the ceiling cover and the
ceiling.

WARNING

!

3.

Push the wires and connectors up into the outlet
box while inserting the receiver fully into the hang-
er bracket. Position the antenna wire on top of the
receiver.

4.

Screw the two 1-1/4” threaded studs (supplied)
into the tapped holes in the hanger bracket (Figure
16).

5.

Lift the ceiling cover up to the threaded studs and
turn until the studs protrude through the holes in
the ceiling cover (Figure 16).

6.

Secure the ceiling cover in place by sliding lock-
washers (supplied) over the threaded studs and
installing the two knurled knobs (supplied). (Figure
16). Tighten the knurled knobs securely until the
ceiling cover fits snugly against the ceiling.

7.

Screw the two 50-watt mini-candelabra base halo-
gen bulbs (supplied) into the light kit plate sockets
(Figure 17). Do not touch the glass bulb; use the
porcelain base to screw in the bulb, or wear soft
gloves.

CAUTION: To avoid risks of burns or other injury,
assure power is off before attempting to install or
replace the halogen bulbs.

NOTICE: Do not touch halogen bulbs with bare
hands. Fingerprints may result in shorter bulb
life. Remove fingerprints with alcohol.

THREADED 
STUD (2)

CEILING 
COVER

KNURLED
KNOB (2)

LOCKWASHER 
(2)

Figure 16

LIGHT KIT 
PLATE

GLASS

50-WATT 
HALOGEN 
BULB (2)

FLAT AREA

Figure 17

8.

Place the lower glass into the light fitter, aligning
the three flat areas on the top flange of the lower
glass with the three pins on the inside of the fitter
(Figure 17). Then turn the lower glass clockwise
until it stops turning.

9.

Your ceiling fan is now installed and wired to be
controlled by your wall control.

U.L. Model No.: CF205

Содержание CF205BS01





















Отзывы: