Emerson Bettis RTS Скачать руководство пользователя страница 13

Страница: 13 / 18

Service Manual

VCIOM-16909-EN Rev. 0

October 2021

Section 4: Manual Actuator Operation Under Maintenance

Manual Actuator Operation Under Maintenance

Section 4: Manual Actuator Operation

Under Maintenance

4.1

Manual Operation

The manual operation is only possible if the actuator is delivered with the optional handwheel. This
option allows an adjustment of the valve in de-energized state.

CAUTION

•

By activating the manual drive, the fail-safe function is disabled.

•

By activating the manual drive, the electrical function of the drive is disabled.

In normal operation, the handwheel (9) has no effect, it rotates idly by.

NOTE:

The manual mode can be activated only when the drive is in the fail-safe position.

Figure 3

Manual handwheel operation

9. Handwheel
10. Coupling Rod
11. Padlock

Содержание Bettis RTS



















Результаты поиска

Содержание Bettis RTS

Отзывы:

Похожие инструкции для Bettis RTS

Бренды по названию

Популярные бренды

Emerson Bettis RTS, Руководство по обслуживанию

Результаты поиска

Содержание Bettis RTS

Отзывы:

Похожие инструкции для Bettis RTS

Бренды по названию

Популярные бренды