Emerson Bettis 2000 Series E796 M2CP Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 27

Emerson Bettis 2000 Series E796 M2CP Скачать руководство пользователя страница 8

5

September 2018

Installation and Maintenance Manual

E2K-402-0817 Rev. 3

M2CP Electrical Hook Up

2.1

Electrical Hook Up

Step 1.

Move valve to mid-position by handwheel. This will allow sufficient time to

stop actuator in case of improper hook-up or reversed incoming power

voltage phases.

Step 2.

Identify a means of removing power from actuator during check out.

Be sure no erroneous remote control signal can be received causing

actuator to energize.

Step 3.

Energize Open control to check operation of contactor and pushbuttons.

Open controls must move valve in Open direction. If valve Closes, actuator

must be stopped and power input must be rewired.

CAUTION

If voltage is improperly phased, Torque and Position Limit Switches are not in circuit to
protect valve.

Step 4.

Seal all field conduit entries in accordance with National Electric Code.

Section 2: M2CP Electrical Hook Up

«
...
6
7
8
9
10
...
»

Содержание Bettis 2000 Series E796 M2CP




























Отзывы:

Нет отзывов