manualshive.com logo in svg
background image

© 2022 Emerson. All rights reserved.

Emerson.com

Before installation, these instructions must be carefully read and understood.

ANDERSON GREENWOOD

 5910C PRESSURE/VACUUM RELIEF VALVE WITH INTEGRATED 

FLAME ARRESTER (ATEX APPROVED)

TABLE OF CONTENTS

1.  Disclaimer of Warranties ............................. 1
2.   Limitations of Seller's Liability .................... 1
3.   Safety Precautions ....................................... 2
4.   Practical Limitations .................................... 2
5.   General .......................................................... 2
6.   Construction ................................................. 2
7.   Operation ....................................................... 3
8.   Installation .................................................... 3
9.   Maintenance ................................................. 4
10. Parts List ....................................................... 6
11.  Special Conditions for Safe Use .................. 7

WARNING

Failure to follow these instructions or to properly 
install and maintain this equipment could result in 
an explosion, fire and/or chemical contamination 
causing property damage and personal injury or 
death.

DISCLAIMER OF WARRANTIES

The contract between Anderson Greenwood 
and our customer states Anderson 
Greenwood’s entire obligation. The contents of 
this instruction manual shall not become part 
of or modify any prior or existing agreement, 
commitment or relationship between Anderson 
Greenwood and our customer. There are no 
express or implied warranties set out in this 
instruction manual. The only warranties that 
apply are those in the existing contract between 
Anderson Greenwood and our customer. 

The Anderson Greenwood 5910C Pressure 
and vacuum relief valves with flame arrester 
assembly have not been tested by Anderson 
Greenwood under all possible operational 
conditions, and Anderson Greenwood does not 
have all the data relative to your application. 
The information in this instruction manual 
is not all-inclusive and does not and cannot 
take into account all unique situations. 
Consequently, you should review this product 
literature in view of your application. If you have 
any further questions, please contact Anderson 
Greenwood for assistance.

LIMITATIONS OF SELLER'S LIABILITY

In the event that a court holds that this 
instruction manual created some new 
warranties, Seller's liability shall be limited 
to repair or replacement under the standard 
warranty clause. In no case shall Seller's 
liability exceed that stated as limitations of 
remedy in the contract between the Seller and 
Buyer. Use of parts that are not manufactured 
or supplied by Anderson Greenwood voids any 
Anderson Greenwood warranty and relieves 
Anderson Greenwood of any obligation to 
service the product under warranty. Anderson 
Greenwood recommends the use of only 
Anderson Greenwood manufactured or 
supplied parts to maintain or service Anderson 
Greenwood 5910C Series Pressure and Vacuum 
relief valve with Flame Arrester assembly.

VCIOM-16612-EN 22/02

FIGURE 1

MODEL 5910C

Содержание ANDERSON GREENWOOD 5910C










Отзывы: