background image

 

 

47 

Series 7400 Single Phase 1+N UPS 

5.1 Introduction 

 

This chapter contains the procedures necessary to effect general 
maintenance of the UPS module and battery.  Certain procedures 

entail gaining internal access to the UPS, and should only be 

undertaken by a competent engineer who is familiar with the 

operation and layout of the equipment and understands the areas 
of potential hazard.  If you have any doubts concerning safety or 

the method carrying out any procedure then contact an approved 

service agent for assistance or advice.  If the locally approved 
agent is known to you, then you should contact the Customer 

Services & Support department at the address shown at the front 

of this manual. 

 
The manufacturer offers customer training, at a nominal fee, if 

required.  Such training can range from a one-day operator course 

to in-depth training on maintenance and troubleshooting lasting 
several days, and can be carried out at the manufacturer’s plant or 

at the customer premises. 

 

 

5.2 Safety Precautions

 

 

When working on the UPS remember that the equipment contains 

live voltages at 

ALL TIMES

 unless it is 

externally 

isolated from the 

mains supply, bypass supply and batteries.  It is essential that the 

safety and precautionary notes contained throughout this manual 

are read and 

FULLY UNDERSTOOD 

before touching any UPS 

internal component part. 

 

5.3 Scheduled Maintenance

 

 

The UPS utilises solid-state components which are not subject to 
wear, with the only moving parts being the cooling fans.  Scheduled 

maintenance requirements, beyond ensuring that the 

environmental conditions remain suitably cool and clean, are 
therefore minimal.  However, a well documented periodic program 

of inspection and preventive maintenance, as suggested below, will 

help to ensure optimum equipment performance and may serve to 

detect certain minor malfunctions prior to them developing into a 
major fault. 

 

Carry out a daily walk-by inspection of the UPS, checking the 
following points: 

 

1.  Carry out a spot check of the operator control panel; ensuring 

that all mimic LED indications are normal, all metered 

parameters are normal and no  warning or alarm messages are 

present on the display panel. 

 
2.  Check for obvious signs of overheating. 

 

3.  Listen for any noticeable change in audible noise. 
 

4.  Ensure that the ventilation grills around the UPS are 

unobstructed. 

 
5.  If possible, log the results of the inspection, noting any 

discrepancies from the norm. 

 

  

  

C h a p t e r   5

C h a p t e r   5   

Maintenance

 

5.3.1  Daily Checks

 

Содержание 7400 Series




































































Отзывы: