manualshive.com logo in svg

Emerson 318-6521, Инструкции по установке и эксплуатации, Страница: 26 / 33

Поделиться
Скачать
Emerson 318-6521 Скачать руководство пользователя страница 26

Document Part # 026-4280 Rev 1 

Page 26 of 33

©2022 Emerson Digital Cold Chain, Inc. This document may be photocopied for personal use. 
Visit our website at www.climate.emerson.com for the latest technical documentation and updates.

14.9.   FHU – Not Used 

This function allows to change the kind of regulation from cooling to heating and vice versa. 

14.10.  Energy Saving Input (ES) 

The Energy Saving function allows to change the setpoint value as the result of the SET+ HES (parameter) sum. This function is 

enabled until the digital input is activated. 

14.11.  Map Switching (NT) 

In this configuration, the digital input activates the map selected by the MP1 parameter. The “MAP CHANGE” MODBUS 

command has higher priority compared to the digital input. 

14.12.  Cleaning Function Activation (CLN) 

In this configuration, the digital input activates the CLEANING function. It can be activated only if the device is ON. 
This function has the following characteristics: 

• The display visualizes the “CLn” label. 
• The light status depends on the LCL parameter (No/Yes), however the light can be modified both via button and MODBUS 

command. 

• The fans status depends on the FCL parameter (No/Yes), furthermore they are not thermo-regulated (par.FST). 

The “CLEANING MODE” MODBUS command has higher priority compared to the digital input. 

14.13.  Defrost End (DEN) 

The digital input ends the defrost cycle in progress. The drip time will follow the defrost end. A further defrost request with the 

digital input active will not be managed. 

14.14.   Digital Inputs Polarity 

The digital inputs polarity depends on “I#P” parameters: CL: the digital input is activated by closing the contact; OP: the digital 

input is activated by opening the contact. 

15 Use of the Programming Hot Key

15.1.   Download (From the Hotkey to the Device)

1. Turn OFF the controller by pressing the on/off button

for five (5) seconds. 

OFF

 will display. Insert the Hot Key into the 

5-pin connector labeled 

HOT-KEY,

 and then turn the controller back ON by pressing the on/off button again for five (5) 

seconds. The normal temperature value will display to indicate the controller is ON.

2. The parameter list of the Hot Key is downloaded into the controller memory automatically and 

doL

 will display. After 10 

seconds, the controller will start working with the new parameters. 

Figure 15-1 - Hot Key

XM controllers can download or upload the parameter list from 
its own non-volatile internal memory to the Hot Key and 
vice-versa through a TTL connector.

Содержание 318-6521


































Отзывы:

Нет отзывов