background image

12

PROGRAMMING 

Cooling

Program

Wake Up

(Morning)

Fan

Leave For Work

(Day)

Fan

 Return Home

(Evening)

Fan

Go To Bed 

 (Night)

Fan

MON

6:00 AM

75°F

Auto 8:00 AM

83°F

Auto 5:00 PM

75°F

Auto 10:00 PM

78°F

Auto

TUE

WED

THU

FRI

SAT

6:00 AM

75°F Auto 8:00 AM

83°F

Auto 5:00 PM

75°F

Auto 10:00 PM

78°F

Auto

SUN

6:00 AM

75°F

Auto 8:00 AM

83°F

Auto 5:00 PM

75°F

Auto 10:00 PM

78°F

Auto

Worksheet for Re-Programming 5+1+1 and 7 Day Program

Heating

Program

Wake Up

(Morning)

Fan

Leave For Work

(Day)

Fan

 Return Home

(Evening)

Fan

Go To Bed 

 (Night)

Fan

MON

6:00 AM

70°F

Auto 8:00 AM

62°F

Auto 5:00 PM

70°F

Auto 10:00 PM

62°F

Auto

TUE

WED

THU

FRI

SAT

6:00 AM

70°F Auto 8:00 AM

62°F

Auto 5:00 PM

70°F

Auto 10:00 PM

62°F

Auto

SUN

6:00 AM

70°F

Auto 8:00 AM

62°F

Auto 5:00 PM

70°F

Auto 10:00 PM

62°F

Auto

Wired Remote Temperature Sensing

One remote temperature sensor can be installed indoor or 
outdoor and connected to the thermostat by a maximum 
cable length of 100 meters (300 feet). Ter, S and - on 
the terminal block allow connection of the remote sensor. 
The thermostat must have 24 VAC Common connection 
to terminal C for the remote sensor to operate. The 
remote sensor can be enabled or disabled in the Installer/
Configuration menu, item 29.
When remote sensor, 

Remote

, is selected 

Off 

(factory 

default), no remote sensor is enabled. When remote sensor is 
selected 

On

, the next step is to select the remote as indoor, 

Remote In

, or outdoor, 

Outdoor Remote

. If the remote is 

selected as Remote In, an additional step will be to select 

if the temperature shown on the display will be from the 
thermostat, 

LS On

, or the remote sensor 

LS Off

.

In normal operation, when a remote sensor is enabled the 
time digits of the display will alternate between the time and 
the remote temperature for three seconds each. Above the 
remote temperature will be Remote, for indoor sensor or 

Outdoor Remote

, for outdoor sensor. If the remote sensor is 

an indoor sensor and the local display has been disabled, the 
temperature displayed as the room temperature will be the 
remote sensor temperature.
Sensing Range: 
Outdoor temperature range is -40

o

F to 140

o

Indoor temperature range is 32

o

F to 99

 o

F

Содержание 1F95-1277















Отзывы: