EMC2 VNX VG2 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 43

background image

26

EMC VNX VG2/VG8 Hardware Information Guide

Component description

Several of the Data Mover I/O modules like the four-port 8-Gb/s Fibre Channel (FC) I/O
module uses SFP or SFP+ transceiver modules to connect to LC-type optical fibre cables.
(The

“Four-port 8-Gb/s FC I/O module” on page 27

provides more detailed information

about the four-port 8-Gb/s FC I/O module.) These SFP or SFP+ transceiver modules are
input/output (I/O) devices that plug into the optical Gigabit Ethernet (GbE) port of the
Data mover I/O modules that use them. These SFP or SFP+ modules are hot swappable.
This means that you can install and remove an SFP or SFP+ module while the VG2/VG8 is
operating.

shows an example of an SFP or SFP+ module.

Figure 21 Example of an SFP or SFP+ module

The LC type interface was developed by Lucent Technologies (hence, Lucent Connector). It
uses a push-pull mechanism. LC connectors are normally held together in a multimode
duplex configuration with a plastic clip. These cables are usually colored orange for OM2
multimode optical fiber type cables and aqua for OM3 multimode optical fiber type
cables. These cables have the duplex connectors encased in a gray plastic covering. To
determine the send or transmit (TX) and receive (RX) ferrules (connector ends), these
cables will show a letter and numeral (for example A1 and A2 for the TX and RX,
respectively) or a white and yellow rubber gasket (jacket) for the send or transmit (TX) and
receive (RX) ends (

Figure 22 on page 27

).

1

Dust plug (protective cap)

3

Send or transmit (TX) optical bore

2

Bale clasp latch

4

Receive (RX) optical bore

CNS-001090

1

2

3

4

«
...
25
26
27
28
29
...
»

Содержание VNX VG2












































Отзывы:

Нет отзывов

Похожие инструкции для VNX VG2

Бренд: YOKOGAWA Страницы: 44

GW-DLMS-485-ELSA15

Бренд: MARCOM Страницы: 13

EliteConnect SMCWHSG14-G

Бренд: SMC Networks Страницы: 2

Бренд: BAB TECHNOLOGIE Страницы: 75

Бренд: ZyXEL Communications Страницы: 323

Бренд: EAE Страницы: 22

MultiVOIP MVP130BG

Бренд: Bogen Страницы: 2

Бренд: Xantrex Страницы: 80

Бренд: Eyedro Страницы: 2

WirelessHART Fieldgate SWG70

Бренд: Endress+Hauser Страницы: 138

Бренд: Fluke Страницы: 20

Бренд: gefran Страницы: 2

3C10122 - NBX Business Telephone

Бренд: 3Com Страницы: 252

Бренд: ENDIAN Страницы: 5

VS-AGU-E1M800-S

Бренд: OpenVox Страницы: 44

Бренд: OpenVox Страницы: 94

Бренд: OpenVox Страницы: 100

Бренд: OpenVox Страницы: 103

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды