EMC EMC VNX VNX5200 Скачать руководство пользователя

Страница: 8 / 18

DC-Powered VNX™ Series Enclosures Installation and Operation Guide

Cabling DC power and powering the system up and down

After installing the storage-system hardware, cable DC power and power up the
system components.

Note: VNX DPEs and DAEs start immediately when connected to active DC input; you
do not need to press or toggle the power switches.

Connect each power supply to a DC power source. See

Figure 3

for systems that

support only block IO;

Figure 4 on page 9

and

Figure 5 on page 10

show typical

unified or file IO configurations.

For high availability, be sure to connect the A and B power cords in each enclosure to
different power source feed circuits.

Note: Grounding screws on the power supplies provide additional grounding
sources, if necessary.

Figure 3 DC power cord connection (Block I/O system)

CL4809

Содержание EMC VNX VNX5200



















Результаты поиска

Содержание EMC VNX VNX5200

Отзывы:

Похожие инструкции для EMC VNX VNX5200

Бренды по названию

Популярные бренды

EMC EMC VNX VNX5200, Инструкция по установке и эксплуатации

Результаты поиска

Содержание EMC VNX VNX5200

Отзывы:

Похожие инструкции для EMC VNX VNX5200

Бренды по названию

Популярные бренды