NOTE:
The system might not be usable for up to three hours if the NVRAM batteries
are discharged. Refer to the NVRAM Battery Charging Instructions for more
information.
Log into the system with the user name of
sysadmin
. The password is the
system’s serial number. A Configuration Wizard is provided. There are six
sections to the configuration: Licenses, Network, File System, System, CIFS,
and NFS.
Complete each of the six sections.
USING THE CLI CONFIGURATION WIZARD
At the first login, the configuration utility starts. The list entries in the utility
can be comma-separated, space-separated, or both.
4
At each prompt, enter a value, OR
4
Enter a question mark (
?
) for more details, OR
4
Press Enter to accept the value displayed in braces.
The Configuration Wizard guides you through the configuration steps, one
section at a time. Follow the Configuration Wizard instructions for entering
appropriate values.
At the end of each configuration section, you can choose to:
4
Save
– Save the displayed configuration.
4
Cancel
– Delete all new values and go to the next section.
4
Retry
– Restart the input entry at the beginning of the current section.
The value entered previously appears as the default value at each prompt.
CONFIGURE THE LUNS
4
Use the
disk show hardware
command to determine the size of
each LUN.
4
To find out which LUNs are available, use the
disk show raid-info
command.
4
Use the
disk rescan
command to discover the LUNs provisioned
from the storage array.
4
Use the
disk add devdisk_id
command to add a LUN to the current
volume. You can add only LUNs with a status of unknown—not already
added to the Data Domain file system.
For more information, see the
DD OS Command Reference Guide
(
disk add
dev
command section).
4
To assign a LUN group to the disk, use this command:
disk set devdisk_id spindle-group 1-16
where the spindle group is identified as a number (1 through 16).
4
There is a maximum of 16 spindle groups. The simplest way to configure
LUNs is to use the same number for both the device and the spindle
group. For example:
# disk add dev2 spindle-group 2
Perform Initial System Configuration
3
SYSTEM SETUP WORKSHEET
An installation requires information unique to your site. Before starting the
installation, provide values for the system information listed below.
1.
A fully qualified host name for the system:
2.
The DNS domain name:
3.
Use Table 1 (below) to enter Ethernet connectivity information.
4.
A routing gateway IP address (if no DHCP):
5.
DNS server IP addresses (if no DHCP) (fill in below):
Primary
Secondary
Tertiary
6.
Select the CIFS authentication method:
Workgroup
Active Directory
Workgroup name:
Realm name:
WINS servers:
WINS servers:
Backup user
name:
Domain admin
name:
Password:
Password:
7.
Backup servers (or * for all):
8.
Administrator’s password:
9.
Host name from which to administer the system:
10.
Administrator’s email address (or admin group alias):
11.
(Optional) Description of the system’s physical location:
12.
Mail server (SMTP) host name:
13.
Time zone name (default is US/Pacific):
14.
System Controller ID from the License Code document provided in
the accessory kit. Use this ID to obtain the unique WWPN for this
controller using the WWPN tool at
https://my.datadomain.com/us/en/wwpn.jsp
Define the Data Domain System Information for Your Site
2
Ethernet Connectivity
eth0
eth1
eth2
eth3
eth4
eth5
Enable (circle one)
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Use DHCP (circle one)
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
IP address (if no DHCP)
Netmask (if no DHCP)
TABLE 1:
