INSTALLATION OF NATURAL GAS PILOT VALVE (cont.)
E. Connect the two 3/8" Street Elbows (Part #16). Screw the 3/8"
threads of the first elbo
w into the outlet of
Place the hole of the Heat Shield (Part #14) over the elbow and slide it down against the body of the elbow
t
Apply pipe compound to the male threads of the elbow and attach it to the control valve outlet.
(See Figure 5)
F.
Attach the 3/8" Natural Gas Orifice (Part #18 or #19) through th
e Burner Pan to the Burner Bar using
the 3/8" Locknut (Part #15, only with Dual Burner log sets). When installing a single burner log
set, a 3/8" locknut is not used. Be sure the small drill hole on the 3/8" Natural Gas Orifice is facing
the gas control valve and the large hole is facing the burner pan.
G.
Using pipe compound, connect the Street Elbow (Part #16, attached to the valve assembly) to the Burner
Orifice (part #18 or #19) on the 3/8" NPT threads.
H.
The valve assembly can be rotated to horizontal, a
nd to allow it to rest on the fireplace floor. Simply rotate
the entire valve assembly
by turning the 3/8" Street Elbow (connected to burner orifice) with a wrench.
(See Figure 5)
I. Attach Pilot Burner Assembly (Part #7) to the Pilot Bracket (Part #8) using the two machine screws (Part #10)
and two nuts (Part #11). See Figure 1A on the previous page. Carefully bend the Pilot tubing (Part #6) when
attaching the Pilot Burner Assembly to the Burner Pan. Care should be taken not to kink the tubing which
would restrict gas flow to the Pilot Burne
r.
NOTE:
The Pilot Bracket utilizes four mounting hol
es for adjustment of the Pilot Burner Assembly should
your installation require repositioning. Repositioning of the Pilot Burner
Assembly may be necessary if the log set is experiencing intermittent
shutdown. Shutdown is caused by overheating of the Pilot Burner
Assembly by the main burner flame. If shut down is
occurring, move
the Pilot Burner Assembly over to the next mounting hole so that only
the tips of the Pilot Burner Assembly are hanging over the Burner Pan.
Only one Mounting Screw (Part #10) will be used in this application.
J. Place the assembled Burner Pan with the Gas Control Valve in the
center of the fireplace.
K.
Connect the 1/2" gas supply line from the fireplace
to the 3/8" Straight
Flared fitting (Part #4) with the 3/8" Flared
T
ubing supplied with the gas
log set. Refer to the General Installation Instructions section titled
“Connecting Gas Supply to Burner Pan” for full instructions.
L.
T
est connections for leaks with soapy water. Retighten if necessary,
and retest the connections to determine if any other leaks are present.
M. Refer the General Installation Instructions for Granule, Ember, Grate
and Log placement.
Figure 5
Figure 3
Figure 4
SINGLE & DUAL SYSTEMS
Outlet
Inlet
Thermocouple
Connection
Pilot Fitting
Connection
Plug
the second.
IMPORTANT: Be sure to turn the pilot adjustment screw with a screwdriver two full turns in a
counter-clockwise
direction to enable pilot operation.
(See Figure 4)
at the point it enters the Gas Control Valve. Line up the mounting holes with the threaded holes in the Gas
Valve. Install the (2) 10 x 24 Heat Shield mounting screws (Part #13) and tighten them at this time.
Gas Control
Knob
Pilot
BAdjustment Screw
Knob Position
Indicator
Burner Pan
Street Elbows
Gas Control Valve
Part # 4
