EmberGlo
A Division of Midco International Inc
8470 77
3
Maintenance
Daily
Installation
Continued
ES10 Steamer Installation and Service
Timers are confi gured as follows:
CYCLE TIME:
Sets the total length of product cooking time, during which steam is
automatically supplied at adjustable intervals. At the end of the set time, steaming stops and
the buzzer sounds. Adjustable from 0.2 to 20 minutes.
STEAM SHOT “ON” TIME:
Sets the amount of time that water is supplied to the steam
generator to create steam. Adjustable from 0.1 to 0.5 seconds.
STEAM SHOT “OFF” TIME:
Sets the amount of the time between steam shots when no
steam is supplied. Adjustable from 6 to 18 seconds.
BUZZER DURATION:
Sets the length of time that the buzzer will sound after automatic
steaming is completed. Adjustable from 0.1 to 10 seconds.
DELAY FROM LAST SHOT TO BUZZER:
Sets the length of time between the last shot
of steam and the sounding of the buzzer. This dwell time allows absorption of steam into
the food. Adjustable from 0.1 to 30 seconds.
The adjustment features have been located within the steamer control box and made accessible
only with a screwdriver in order to discourage tampering or readjustments by unauthorized
personnel.
DANGER: Use extreme caution when adjusting timers. Bare wire terminals and/or bare
wires are exposed. Unplug male twist-lock plug or use extreme caution if steamer is
plugged in when making timer adjustments. Use an insulated or fi berglass screw driver.
IMPORTANT: KEEP LID CLOSED WHEN NOT IN USE.
This keeps the food pan hot and reduces
condensation in the steam chamber. When steamer is fi rst installed, or when reconnecting water
hose, operate
STEAM
button several times to purge air from lines.
____________________________________
Food Pan and Grid
on all models should be removed and washed with a detergent or run
through a dishwasher.
WARNING: Under no circumstances should the entire Steamer be run through a
dishwasher. If any of the switches or timers in electric control compartment get wet they
can malfunction. Never try to use a device that has been wet—replace it.
All exposed stainless steel surfaces should be wiped with a damp cloth or cleaned with a chlorine
free stainless steel cleaner. Rust spots can develop on stainless steel surfaces that are not
cleaned daily.
____________________________________
Do not connect to a circuit operating
at more than 150 Volts to ground
Input
208V/240V/60 Hz
Neutral
Power
Switch
BK
Thermal Cut-off
BR
BK
BK
R/BK
W
BK
W
Heating
Element
1600W
Thermostat
120V
120V
GND
4
2
5
1
Buzzer
1425-00
Buzzer
Duration
2528-10
Hot
Neut
2
3
Y
1M
BL
BL
2528-00
Buzzer
Delay
Y
Water
Solenoid
Valve
8402-26
7
6
Ext
Res
BL
Buzzer Timer
8406-63
1
4
COM NO
BL/W
1
2
3
4
1
2
3
4
1M
2528-20
Wiring for ES10 Steamer
with 101 or 102 control
OR
OR
610K
1M
BL/W
BR
BR
9
8
Ext Res
BR
3
2
1
Neut
Hot
Load
Shot Timer
On
Time
Off
Time
BL/W
BL/W
22K
100K
Y
NC
NO
COM
HOT
Neut
1
8
9
2
3
6
7
5
Ext Res
Cycle
Timer
1M
2528-40
Cycle
Time
SW
8406-64
W
BK
OR/BK
2528-30
R
W
R/BK
BL
BK
W
R/BK
W
R
BL
BL
1
2
3
4
1
2
3
4
3
6
6
3
2
5
5
2
1
4
4
1
OR/BK
3
4
2
1
Steam
Button
R
BK
BK
Thermostat
Heating
Element
1600W
BK
Thermal
Cut-Off
R
R
Y
8406-62
Manual
Cycle
8423-35
6
Figure 1: Wiring Diagram
