EMB Wallenstein HUF12000E Скачать руководство пользователя страница 23

Страница: 23 / 36

HUF12000EA

A. Voltmeter meter monitors and displays the

voltage being produced by the generator. The

top scale displays the 120 Volt range and the

bottom, the 240 Volt.

B. These two GFCI protected outlets (5-20R) are

used to provide 120 Volt, 20 Amp power.

C. This outlet (L5-30) is used to provide 120 Volt,

30 Amp power.

D. This outlet (L14-30) is used to provide 120/240

Volt, 30 Amp power .

E. These outlets (6-50R & 14-50R) are used to

provide 120/240 Volt, 50 Amp power.

F. These 20 Amp breakers are used to protect

the 20 Amp 120 Volt outlets (B). Push the

switch to reset.

G. This 30 Amp circuit breaker protects the two

30 Amp out lets (C&D). Move the switch up to

engage the breaker and down to disengage.

H. Main Switch / 50 Amp breaker protects the

two 50 amp outlets (E) and is the master

overload for the generator. Move the switch

up to engage the breaker and down to disen-

gage the breaker.

I. Automatic Idle Control is a fuel & time saving,

convenience feature. See below for details.

IMPORTANT

A circuit breaker that trips repeat-

edly may indicate a problem.

5.53 ELECTRICAL CONTROLS: HUF12000EA

1. Automatic Idle Control is a fuel saving, conven-

ience feature. The auto idle module uses six

selectable preset times (in seconds), to set the

length of delay before the engine goes to low idle.

The module will sense when power is not being

used and will automatically idle down after the

delay time, saving time and fuel.

2. Normal Generating Indicator: on, indicating nor-

mal operation, off at auto idle.

3. Over Voltage Indicator: off, indicating normal op-

eration, on, indicating an over voltage condition:

unit should be shut off and serviced.

4. Hour Meter / Oil Use Meter measures and displays

the time the generator has been operating and can

display the hours the oil has been in use since the

last oil change.

To select between hour and oil use display, find

the rubber push button located under the module,

accessed thru the notch in the panel.

a. Momentarily depressing the button switches

the display.

b. To reset the oil use hours after changing the

oil, depress the button for 2 seconds.

Hour / Oil display

/ reset button

Содержание Wallenstein HUF12000E





































Результаты поиска

Содержание Wallenstein HUF12000E

Отзывы:

Похожие инструкции для Wallenstein HUF12000E

Бренды по названию

Популярные бренды

EMB Wallenstein HUF12000E, Руководство оператора

Результаты поиска

Содержание Wallenstein HUF12000E

Отзывы:

Похожие инструкции для Wallenstein HUF12000E

Бренды по названию

Популярные бренды