emaux TMG Series, Руководство пользователя

Страница: 2 / 2

1
2
3
4
5
6
7
8
9
10
11
12 13 15
14
16
17 15 18
19
20
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
18 19
20
21
16
17
2
3
9
13
7
6
10
11
12
1
4
5
6
8
1
2
3
4
5
6
8
7
14
15
2-4
REPLACEMENT PARTS OF FILTER
3-4
1) Make sure the correct amount of filter media sand is located in the tank and all connections have been
connected and secured.
2) Depress control valve handle and rotate to BACKWASH position. (To prevent damage to control valve seal, always
depress handle before turning.)
3) Prime and start pump according to pump instructions (be sure all suction and return lines are open), allowing the
filter tank to fill with water. Once water is flowing out of the waste line, run the pump for at least 1 minute. The initial
back-washing of the filter is recommended to remove any impurities or fine sand particles in the sand media.
4) Turn pump off and set valve to RINSE position. Start pump and operate until water in sight glass is clear, about 1/2 to
1 minute. Turn pump off and set valve to FILTER position and restart pump. The filter is now operating in the normal
filter mode, filtering dirt particles from the pool water.
5) Adjust pool suction and return valves to achieve desired flow. Check system and filter for water leaks and tighten
connections, bolts, nuts, as required.
6) Note the initial pressure gauge reading when the filter is clean. (It will vary from pool to pool depending upon the
pump and general piping system.) As the filter removes dirt and impurities from the pool water, the accumulation
of dirt in the filter will cause the pressure to rise and diminish the water flow. When the pressure gauge reading is 1.5
bar, higher than the initial "clean" pressure you noted, it is time to backwash the filter (see BACKWASH under filter
and control valve functions).
INSTALL/START-UP OF FILTER
REPLACEMENT PARTS OF 1.5" MULTIPORT VALVE (TMG500 / TMG650)
NOTE: During initial clean-up of the pool water it may be necessary to backwash frequently due to the unusually
heavy initial dirt load in the water.
REPLACEMENT PARTS OF 2" MULTIPORT VALVE (TMG650(B))
Key
No.
Part No. Description Qty
1 88281550B 6 Way 1.5" Valve (Black) with union set (Top Mount) 1
1 88281551B 6 Way 2" Valve (Black) with union set (Clamp type) 1
1 88280356
6 Way 2" Valve (Black) with piping, union set (Top
Mount)
1
2 06011029 Oil Pressure Gauge with O-Ring (40Psi) 1
3 89280102B 1.5" union set (Black) with O-ring 3
3 89280103B 2" union set (Black) with O-ring 3
4 89010657 Filter Tank with base for TMG500 1
4 89010658 Filter Tank with base for TMG650 1
4 89010659 Filter Tank with base for TMG650B 1
4 89010660 Filter Tank with base for TMG750 1
4 89010661 Filter Tank with base for TMG900 1
5 89010662 Lateral Assembly with Centre Pipe for TMG500 1
5 89010663 Lateral Assembly with Centre Pipe for TMG650 1
5 89010664 Lateral Assembly with Centre Pipe for TMG650B 1
5 89010665 Lateral Assembly with Centre Pipe for TMG750 1
5 89010666 Lateral Assembly with Centre Pipe for TMG900 1
6 01172007 Laterals (115mm) *
6 01172008 Laterals (126mm) *
6 01172010 Laterals (185mm) *
7 89011601 Water Drain Set 1
8 01112074 Filter Base (D500*89 1
8 01112075 Filter Base (D390*73) 1
9 03021035 M6 Nut 1
10 89012512 Clamp Kit 1
11 01111101 Star-Shaped Nut 1
12 03011166 M6×110mm Screws 1
13 02010007 O-Ring 1
14 89010601 Nut with Washer 1
15 02011126 Filter Neck Gasket 1
Notes:
TMG
TMG650 should have 8pcs of Lateral (126mm)
TMG650B should have 4pcs of Laterals (115mm) & 4pcs of (126mm)
TMG750 and TMG 900 should have 8 pcs of Laterals (185mm) 500 should have 8pcs of Lateral (115mm)
Item Part No. Description Qty
1 01013003 Handle (Big) 1
2 03018008 Pin for Handle 1
3 01181027 Washer for Handle 1
4 01181029 Defend Lock 1
5 01020003 1.5" Lid 1
6 01181002 Washer for Spring 1
7 02011022 O-Ring for Valve Rotor 2
8 03014001 Spring 1
9 89280701 1.5" Valve Rotor with Spider Gasket 1
10 02010002 O-Ring for Lid 1
11 E190136 1.5" Body with Diffuser 1
12 02020013 O-Ring for 1.5"Connector 3
13 01013015 1.5" Connector (Black) 3
13 01051013 1.5" Connector (White) 3
14 02011003 O-Ring for 1.5" Adaptor 3
15 01171153 1.5" Union (A/E) 3
16 01013017 1.5" Union Nut (Black) 3
16 01051014 1.5" Union Nut (white) 3
17 89280120 Drain Plug Fitting with O-ring 1
18 89021307 Drain Plug with O-Ring 1
19 06021013 Pressure Gauge with O-Ring (40Psi) 1
20 89280104 Sight Glass with O-Ring 1
21 02011001 O-Ring for Diffuser 1
Item Part No. Description Qty
1 01013003 Handle (Big) 1
2 03018008 Pin for Handle 1
3 01181027 Washer for Handle 1
4 01181028 Defend Lock 1
5 01020009 2.0" Lid 1
6 01181002 Washer for Spring 1
7 02011022 O-Ring for Valve Rotor 2
8 03014014 Spring for Valve 1
9 89280805 2.0" Valve Rotor with Spider Gasket 1
10 02010003 O-Ring for Lid 1
11 E190213 2.0" Body with Diffuser 1
12 89280120 Drain Plug Fitting with O-ring 1
13 89021307 Drain Plug with O-Ring 1
14 06011029 Oil Pressure Gauge with O-Ring (40Psi) 1
15 02020016 1.5" Union Nut (Black) 6
16 01013031 2.0" Connector (Black) 3
17 01171154 2.0" Union (A/E) 3
18 01013032 2.0" Union Nut (Black) 3
19 89280104 Sight Glass with O-Ring 1
20 02011005 O-Ring for Diffuser 1