2-4
3-4
REPLACEMENT PARTS OF MULTIPORT VALVE
820
920
Model
A
High
mm
B
Diameter
mm
1020
1130
S800R
S900R
723
920
S700R(B)
Valve Port
Size
Inch
Sand
Kg
2”
2”
2”
355
470
215
2
3
1
4
5
6
7
9
10
11
12
14
16
15
13
17
18
19
20
22
21
24
25
26
23
27
8
REPLACEMENT PARTS OF FILTER
Key
No
.
Part
No
.
Product
Description
Qty
1
01013003
Handle
(
Big
)
1
2
03018008
Pin
for
Handle
1
3
01181027
Washer
for
Handle
1
4
01013022
2
.
0
"
Side
Mount
Valve
Rotundity
Lid
(
Black
)
1
5
89280301
M6
*
32
Screw
with
Nut
10
6
01111048
Connector
for
Pressure
Gauge
/
Stopper
1
7
89021303
Drain
Plug
with
O
'
Ring
1
8
06011029
Oil
Pressure
Gauge
With
O
-
ring
(
40psi
)
1
9
02020016
O
-
Ring
for
2
.
0
"
Union
8
10
01013031
2
.
0
"
Connector
(
Black
)
3
11
01171154
2
.
0
"
Union
(
A
/
E
)
3
12
01013032
2
.
0
"
Union
Nut
(
Black
)
3
13
02011009
O
-
Ring
for
2
.
0
"
Valve
Lid
1
14
01181002
Washer
for
spring
1
15
02011022
O
-
Ring
for
2
.
0
"
Valve
Rotor
2
16
03014014
Spring
1
17
01021002
2
.
0
"
Valve
Rotor
1
18
02311003
Spider
Gasket
1
19
01013026
2
.
0
"
Side
Mount
Valve
Bottom
Body
(
Black
)
1
20
89280104
Sight
Glass
With
O
-
Ring
1
21
02011011
O
-
Ring
for
Union
Tale
1
22
01013099
2
.
0
"
Union
Tale
(
Black
)
1
23
01013034
2
.
0
"
Union
Nut
(
Black
)
2
24
02020017
O
-
Ring
for
Plug
1
25
01013101
2
.
0
"
Side
Mount
Valve
Plug
(
Black
)
2
26
01013118
2
.
0
"
Elbow
Tube
(
Black
)
183mm
1
27
01171035
2
.
0
"
Union
Adaptor
(
Metric
)
1
MAIN DIMENSION
DIMENSION
TABLE
B
A
3)
Tighten the Ring Lock Nut by 2 handles and make sure the nut is “sand free” on its thread.
a)
)
4) Connect pump to control valve opening marked PUMP.
5) Make return to pool pipe connection to control valve opening marked RETURN and complete other
necessary plumbing connections, suction lines to pump, waste, etc.
6) Make electrical connections to pump per pump instructions.
7) To prevent water leakage, be sure all pipe connections are right.
Install the valve.
Carefully screw the T-shape Exhaust Switch onto the filter lid and make sure there do not over-tighten.
b Ensure T-Shape Exhaust switch is tight fit to filter lid and turn it easily.
1) Be sure correct amount of filter media sand is in tank and that all connections have been made and are secure.
2) Depress control valve handle and rotate to BACKWASH position. (To prevent damage to control valve seal,
always depress handle before turning.)
3) Prime and start pump according to pump instructions (be sure all suction and return lines are open), allowing the
filter tank to fill with water. Once water is flowing out of the waste line, run the pump for at least 1 minute. The
initial back-washing of the filter is recommended to remove any impurities or fine sand particles in the sand
media.
4) Turn pump off and set valve to RINSE position. Start pump and operate until water in sight glass is clear, about 1/2
to 1 minute. Turn pump off and set valve to FILTER position and restart pump.The filter is now operating in the
normal filter mode, filtering dirt particles from the pool water.
5) Adjust pool suction and return valves to achieve desired flow. Check system and filter for water leaks and
tighten connections, bolts, nuts, as required.
6) Note the initial pressure gauge reading when the filter is clean. (It will vary from pool to pool depending upon the
pump and general piping system.) As the filter removes dirt and impurities from the pool water, the
accumulation in the filter will cause the pressure to rise and flow to diminish. When the pressure gauge reading is
1.5 bar, higher than the initial "clean" pressure you noted, it is time to backwash the filter (see BACKWASH under
filter and control valve functions).
NOTE: During initial clean-up of the pool water it may be necessary to backwash frequently due to the unusually
heavy initial dirt load in the water.
INSTALL/START-UP OF FILTER
Key No.
Part No.
Description
Qty
1
01021004
Spanner for RingLock
1
2
01271013
2.0" Ringlock Nut
1
3
06011029
Oil Pressure Gauge With O-ring
1
4
89014027
T-Shape Exhuaust Switch
1
5
01201020
Cover
1
6
02011036
O-Ring for Cover
1
7
89011212
S800 RINGLOCK Filter Tank With Base
1
7
89011213
S900 RINGLOCK Filter Tank With Base
1
8
89011203
The inner tank system for S700R(B)
1
8
89011210
The inner tank system for S800( R)(B)
1
8
89011211
The inner tank system for S900( R)(B)
1
9
01101065
2.0"Tank System Support
1
10
02020016
2.0" O-Ring for Connector
1
11
88280813B
6 Way 2" Valve with Piping Kit, 2" union
set x 3 and pressure gauge (Black)
1
12*
01172010
Laterals (185mm) For S800R
8
12*
01172011
Laterals (233mm) For S900R
8
13
01112038
32-40 inch Filter Base
1
14
89010107
Water Drain set
1
Note:12* S800R should have 8pcs of Laterals (185mm)
12* S900R should have 8pcs of Laterals (233mm)
