background image

3

 

EMS-122/122w User Manual 

www.emacoustics.co.uk 

INTRODUCTION 

Thank you 

 
Thank you for purchasing a product from the acclaimed EMS Series from EM Acoustics.  The EMS  Series products 

have been carefully designed and rigorously tested to ensure years of flawless operation and unprecedented sonic 

quality.  Flexibility is the key factor with EMS products, and consequently they are at home within a wide variety of 

applications  from  live  and  portable  applications,  through  to  cafes,  bars,  nightclubs,  theatres  and  conference 

centres.   

 

Please ensure that you read this manual carefully before use, and that you keep it to hand should you need it for 

further  reference.    Furthermore,  should  you  have  any  difficulties  please  do  not  hesitate  in  contacting  your  EM 

Acoustics dealer, or email 

[email protected]

 for further assistance. 

 

Unpacking 

 

Every  EM  Acoustics  product  is  built  to  the  highest  standard  and  thoroughly  tested  before  it  leaves  our  factory.  

After unpacking your loudspeaker, please inspect it carefully for any signs of transit damage.  If such damage is 

found, please notify the carrier at once to instigate a claim.  It is suggested that you retain all packaging for future 

re-shipment. 

 
DECLARATION OF CONFORMITY 

 

The  products  contained  within  this  manual  conform  to  the  requirements  of  the  EMC 

Directive  89/336/EEC,  amended  by  92/31/EEC  and  to  the  requirements  of  the  Low 

Voltage Directive 73/23/EEC amended by 93/68/EEC. 

 

Standards Applied: 

 

EMC   Emission 

EN55103-1:1996 

 

 

 

 

 

Immunity 

EN55103-2:1996 

 

 

 

 

Electrical Safety  

EN60065:1993 

RECYCLING 

This product and its packaging constitute the applicable product according to the WEEE directive.  

Please  ensure  that  at  the  end  of  the  working  life  of  this  product,  it  is  disposed  of  sensibly  in 

accordance with local and national recycling regulations.  The packaging supplied with this product 

is  recyclable.    Please  retain  all  packaging,  however  if  disposing  of  this  packaging  please  ensure 

that  you  comply  with  local  recycling  regulations.  These  products  also  all  comply  to  the  RoHS 

Directive 2002/95/EC. 

Содержание EMS-122














Отзывы: