Elvox SL24.W Скачать руководство пользователя страница 8

Страница: 8 / 24

SL24.W

6 - Control panel programming:

6.1 - Preliminary operations

To function correctly, the control panel requires some minimum and essential settings. There are two:

- Setting the motor type.

In its default configuration, the control panel is not associated to any type of motor. The type of motor associated to the

control panel must be set.

- Gate travel calibration

The control panel must know some physical parameters of the gate in order to function correctly. The operation allowing

the control panel to know these physical gate parameters is called travel calibration. If this is not done, the control panel

may not perform slowdowns or detect obstacles correctly.

6.2 - Using the display

The control panel is programmed using the display and the navigation buttons on board or via Smartphone/Tablet (see

paragraph "Wi-Fi connection to Smartphone/Tablet"). The control panel settings are shown on the display and can be

edited using the menu navigation buttons as shown in the following table:

Buttons

Function

Pressure length

Switching on the display

Sub-menu entry

Confirm value change and return to menu

Instantaneous

▲

Scroll up

Increase parameter value

Instantaneous

▼

Scroll down

Reduce parameter value

Instantaneous

ESC

Exit the menu

Cancel value change and return to menu

Switching off the display

Instantaneous

▲+▼

Resetting the card

3 s

▲+ OK

Opening control

1 s

▼+ OK

Closing control

1 s

ESC + OK

Display test (switches on each segment of the display and points individually in

sequence)

3 s

ESC + OK

When the board is switched on the Firmware updating mode starts

3 s

Step-step control

Instantaneous

6.3 - Menu

The control panel programming is organised into menus and sub-menus used to access and edit the parameters and

logics of the control panel. The control panel is equipped with the following first-level menus:

All sub-menus are described in the following table

Menu

Description

MOT

Motor parameters setup

LRNT

Travel calibration procedure run menu

TRV

Travel parameter settings menu

OUT

Auxiliary output configuration menu

Input configuration menu

LGC

Operating logic settings menu

RAD

Remote control management menu

STAT

Diagnostic and reporting menu

EXP

Expansion board management menu

LOAD

Default value restore menu

PASS

Protection level settings menu

Содержание SL24.W

























Результаты поиска

Содержание SL24.W

Отзывы:

Похожие инструкции для SL24.W

Бренды по названию

Популярные бренды

Elvox SL24.W, Руководство по установке

Результаты поиска

Содержание SL24.W

Отзывы:

Похожие инструкции для SL24.W

Бренды по названию

Популярные бренды