© 2020, Elvaco AB. All rights reserved. The documentation and product are provided on an “as is” basis only and may contain deficiencies or in-
adequacies. Elvaco AB takes no responsibility for damages, liabilities or other losses by using this product. No part of the contents of this manual
may be transmitted or reproduced in any form by any means without the written permission of Elvaco AB. Printed in Sweden.
CMi5110 Quick manual A4 English
Document id: 1090075
Version: 8.0
Mechanics
Protection class
IP20
Mounting
In CMi-Box module slot
Electrical connections
Power supply
Board connector 2 mm
M-Bus slave port
Screw terminal 0.5-2.5 mm²
Antenna
Built-in, or optionally external via SMA-f
Electrical characteristics
Nominal voltage
230 V power supply: 100-240 VAC, 24 V power
supply: 12-35 VAC or 12-48 VDC, Internal power
supply: 4 VAC
Frequency
50/60 Hz
Power consumption
<0.2 W
Installation category
CAT 2
Wireless M-Bus Receiver
Wireless M-Bus modes
S1, T1, C1
Maximum number of wireless
M-Bus devices
800
Radio frequency band
868 MHz
Encryption
AES-128, OMS
RF sensitivity (standard /
amplified version)
-104 dBm / -109 dBm
M-Bus slave interface
M-Bus baud rate
300 and 2400 bit/s
Power consumption
1T/1.5 mA
Approvals
EMC
EN 61000-6-2, EN 61000-6-3
Safety
EN 61010-1, CAT 2
Product
Part No
Description
CMi5110I
1050067
Wireless M-Bus master internal antenna
CMi5110E
1050064
Wireless M-Bus master external antenna
Power supply 230 V
1050053
Power supply 230 V
Power supply 24 V
1050055
Power supply 24 V
Magnet antenna
9950470
868 MHz SMA 1.5 m
Omni antenna
9950472
7.1 dBi 824-890 MHz
Omni antenna
9950500
2.15 dBi 824-890 MHz
ORDERING INFORMATION
CONTACT TECHNICAL SUPPORT
Phone: +46 300 434300
E-mail: support @elvaco.com
Online: www.elvaco.com
TECHNICAL SPECIFICATIONS
M-BUS SLAVE PORT
The product is equipped with an M-Bus slave port to enable wide
integration. The port can be used to read the connected wireless M-Bus
slaves as normal M-Bus slaves. Slaves can be read using primary and/
or secondary addressing. The CMi5110 itself is available as an M-Bus
slave with the secondary address equal to the serial number. The M-Bus
2-wire interface acts like any other M-Bus slave device on the 2-wire
bus. The nominal current is 1T (1.5 mA). This interface can be directly
used with any standard M-Bus master.
GETTING STARTED
If CMi5110 should be able to deliver readings from wireless meters, these
must first be installed. This can be made in two ways:
Option 1: Press button (2 in overview) to start the installation on
CMi5110. When the installation mode is started, the blue LED will light
up. The red LED will be on until a meter is installed.
Option 2: Start the installation via M-Bus commands, for example via
Elvaco’s CMe3100. This allows easy adjustments and administration of
parameters and meter list.
LED INDICATIONS
LED
State
Description
Red
On
Meter list empty, no meters installed
Green
50/50
Power ON, operation
Yellow
Short flash
Receives data from meter
Blue
On
Product is in installation mode
TROUBLESHOOTING
When running installation, no wireless meters are found (Red LED on)
Please verify:
•
CMi5110 antenna installation and position.
•
Wireless M-Bus slave mode must be the same as configured
CMi5110 wireless M-Bus mode.
CMi5110 does not respond to M-Bus master commands
Please verify M-Bus status:
•
Voltage over M-Bus slave device should be between 21-42 VDC.
•
All M-Bus slave devices must have unique secondary or primary
M-Bus addresses depending on addressing mode.
•
Verify M-Bus slave baud rate used by M-Bus master. M-Bus master
baud rate must be identical to the CMi5110 baud rate.
•
Encrypted wireless M-Bus slaves without uploaded keys will send
meter data in container mode. Add keys to corresponding meter
using M-Bus commands.
FACTORY RESET
Turn off power. Press push button (2) and turn on power. Keep pressing
the button for 10 s, until the red and yellow LED is flashing.
SAFETY
The warranty does not cover damage to the product caused by usage in
any other way than described in this manual. Elvaco AB can not be liable
for personal injury or property damage caused by usage in any other way
than described in this manual.
Products:
Products:
Products:
Products:
This declaration of
Elv
Product
CMip2110 L+G UH50 PS 2
The object(s) of the decla
EMC Directive
RoHS 2011/65
And are in conformity wit
EN55022 (Rad
EN 61000‐4‐6
EN 61000‐4‐3
EN 61000‐4‐11
EN 61000‐4‐4
EN 61000‐4‐5
EN 61000‐4‐2
Kungsbacka,
Sweden,
201
David
Vonasek,
CEO
This declaration of
Elv
Product
CMip2110 L+G UH50 Bat.
The object(s) of the decla
EMC Directive
RoHS 2011/65
And are in conformity wit
EN55022 (Rad
EN 61000‐4‐6
EN 61000‐4‐2
Kungsbacka,
Sweden,
201
David
Vonasek,
CEO
This declaration of
Elv
Product
CMi1020
The object(s) of the decla
LVD Directive
EMC Directive
RoHS 2011/65
And are in conformity wit
IEC 61010‐1 (e
EN55022 (Rad
EN 61000‐4‐6
EN 61000‐4‐3
EN 61000‐4‐11
EN 61000‐4‐4
EN 61000‐4‐5
EN 61000‐4‐2
Kungsbacka,
Sweden,
201
David Vonasek, CEO
This declaration of
Elv
Product
CMip2130
The object(s) of the decla
LVD Directive
EMC Directive
RoHS 2011/65
And are in conformity wit
IEC 60950‐1
EN55022 (Rad
EN 61000‐4‐6
EN 61000‐4‐3
EN 61000‐4‐11
EN 61000‐4‐4
EN 61000‐4‐5
EN 61000‐4‐2
Kungsbacka,
Sweden,
201
David Vonasek, CEO
CMip2110
L+
CMip2110
L+
CMi1020
CMip2130
EU DECLARATION OF C
f conformity is issued under the s
vaco AB, Teknikgatan 18, S‐434 37
Year of CE‐marking
24VAC 2016
aration listed above is in conformity with the
e 2014/30/EU
5/EU
th the following harmonization standards or
diated emission)
(Immunity to HF‐injection)
(Immunity to RF‐field)
1 (Immunity to voltage variation)
(Immunity to burst)
(Immunity to surge)
(Immunity to ESD)
16
‐
04
‐
16
EU DECLARATION OF C
f conformity is issued under the s
vaco AB, Teknikgatan 18, S‐434 37
Year of CE‐marking
. Backup 2016
aration listed above is in conformity with the
e 2014/30/EU
5/EU
th the following harmonization standards or
diated emission)
(Immunity to HF‐injection)
(Immunity to ESD)
16
‐
04
‐
16
EU DECLARATION OF C
f conformity is issued under the s
vaco AB, Teknikgatan 18, S‐434 37
Year of CE‐marking
2016
aration listed above is in conformity with the
2014/35/EU
e 2014/30/EU
5/EU
th the following harmonization standards or
ed.3)
diated emission)
(Immunity to HF‐injection)
(Immunity to RF‐field)
1 (Immunity to voltage variation)
(Immunity to burst)
(Immunity to surge)
(Immunity to ESD)
16
‐
04
‐
16
EU DECLARATION OF C
f conformity is issued under the s
vaco AB, Teknikgatan 18, S‐434 37
Year of CE‐marking
2016
aration listed above is in conformity with the
2014/35/EU
e 2014/30/EU
5/EU
th the following harmonization standards or
diated emission)
(Immunity to HF‐injection)
(Immunity to RF‐field)
1 (Immunity to voltage variation)
(Immunity to burst)
(Immunity to surge)
(Immunity to ESD)
16
‐
04
‐
16
+G
UH50
PS
24
+G
UH50
Bat.
B
CONFORMITY
sole responsibility of the manufac
7 Kungsbacka, Sweden.
e relevant Community harmonization legislat
r other normative documents:
CONFORMITY
sole responsibility of the manufac
7 Kungsbacka, Sweden.
e relevant Community harmonization legislat
r other normative documents:
CONFORMITY
sole responsibility of the manufac
7 Kungsbacka, Sweden.
e relevant Community harmonization legislat
r other normative documents:
CONFORMITY
sole responsibility of the manufac
7 Kungsbacka, Sweden.
e relevant Community harmonization legislat
r other normative documents:
4VAC
Backup
cturer:
tion:
cturer:
tion:
cturer:
tion:
cturer:
tion:
P
P
P
P
Products:
CMi2
Products:
CMi2
Products:
CMi5
Products:
CMiB
EU DECL
This declaration of conformity
Elvaco AB, Tek
Product
Year of
CMi2130A
2016
The object(s) of the declaration listed abo
LVD Directive 2014/35/EU
EMC Directive 2014/30/EU
Radio Equipment Directive 20
RoHS 2011/65/EU
And are in conformity with the following
EN55022 (Radiated emission)
EN 61000‐4‐6 (Immunity to HF
EN 61000‐4‐3 (Immunity to RF
EN 61000‐4‐11 (Immunity to v
EN 61000‐4‐4 (Immunity to bu
EN 61000‐4‐5 (Immunity to su
EN 61000‐4‐2 (Immunity to ES
EN 300 220‐1 (SRD Low power
EN 3010511:v.9.0.2 (Gemalto)
Kungsbacka,
Sweden,
2016
‐
04
‐
16
EU DECL
This declaration of conformity
Elvaco AB, Tek
Product
Year of
CMi2140E
2016
The object(s) of the declaration listed abo
EMC Directive 2014/30/EU
Radio Equipment Directive 20
RoHS 2011/65/EU
And are in conformity with the following
IEC 61010‐1 (ed.3)
EN55022 (Radiated emission)
EN 61000‐4‐6 (Immunity to HF
EN 61000‐4‐3 (Immunity to RF
EN 61000‐4‐11 (Immunity to v
EN 61000‐4‐4 (Immunity to bu
EN 61000‐4‐5 (Immunity to su
EN 61000‐4‐2 (Immunity to ES
EN 300 220‐1 (SRD Low power
EN 300220‐2
EN 3010511:v.9.0.2 (Gemalto)
Kungsbacka,
Sweden,
2016
‐
04
‐
16
EU DECL
This declaration of conformity
Elvaco AB, Tek
Product
Year of
CMi5110E
2016
CMi5110I
2016
The object(s) of the declaration listed abo
EMC Directive 2014/30/EU
RoHS 2011/65/EU
And are in conformity with the following
EN55022 (Radiated emission)
EN 61000‐4‐6 (Immunity to HF
EN 61000‐4‐3 (Immunity to RF
EN 61000‐4‐11 (Immunity to v
EN 61000‐4‐4 (Immunity to bu
EN 61000‐4‐5 (Immunity to su
EN 61000‐4‐2 (Immunity to ES
EN 300 220‐1 (SRD Low power
Kungsbacka,
Sweden,
2016
‐
04
‐
16
David
Vonasek,
CEO
EU DECL
This declaration of conformity
Elvaco AB, Tek
Product
Year of
CMiB Wmbus IA24
2016
CMiB Wmbus IA230
2016
CMiB Wmbus EA24
2016
CMiB Wmbus EA230
2016
CMiB Wmbus GIA24
2016
CMiB Wmbus GIA230
2016
CMiB Wmbus GEA24
2016
CMiB Wmbus GEA230
2016
The object(s) of the declaration listed abo
LVD Directive 2014/35/EU
EMC Directive 2014/30/EU
Radio Equipment Directive 20
RoHS 2011/65/EU
And are in conformity with the following
IEC 61010‐1 (ed.3)
EN55022 (Radiated emission)
EN 61000‐4‐6 (Immunity to HF
EN 61000‐4‐3 (Immunity to RF
EN 61000‐4‐11 (Immunity to v
EN 61000‐4‐4 (Immunity to bu
EN 61000‐4‐5 (Immunity to su
EN 61000‐4‐2 (Immunity to ES
EN 300 220‐1 (SRD Low power
EN 300220‐2
EN 3010511:v.9.0.2 (Gemalto)
Kungsbacka,
Sweden,
2016
‐
04
‐
16
David
Vonasek,
CEO
2130A
2140E
5110E,
CMi51
B
Wmbus
(CM
LARATION OF CONFOR
y is issued under the sole responsi
knikgatan 18, S‐434 37 Kungsbacka
f CE‐marking
ove is in conformity with the relevant Comm
014/53/EU
harmonization standards or other normative
F‐injection)
F‐field)
voltage variation)
urst)
urge)
SD)
r radio equipment)
)
LARATION OF CONFOR
y is issued under the sole responsi
knikgatan 18, S‐434 37 Kungsbacka
f CE‐marking
ove is in conformity with the relevant Comm
014/53/EU
harmonization standards or other normative
F‐injection)
F‐field)
voltage variation)
urst)
urge)
SD)
r radio equipment)
)
LARATION OF CONFOR
y is issued under the sole responsi
knikgatan 18, S‐434 37 Kungsbacka
f CE‐marking
ove is in conformity with the relevant Comm
harmonization standards or other normative
F‐injection)
F‐field)
voltage variation)
urst)
urge)
SD)
r radio equipment)
LARATION OF CONFOR
y is issued under the sole responsi
knikgatan 18, S‐434 37 Kungsbacka
f CE‐marking
ove is in conformity with the relevant Comm
014/53/EU
harmonization standards or other normative
F‐injection)
F‐field)
voltage variation)
urst)
urge)
SD)
r radio equipment)
)
10I
Mi
‐
Box
X)
RMITY
ibility of the manufacturer:
a, Sweden.
unity harmonization legislation:
e documents:
RMITY
ibility of the manufacturer:
a, Sweden.
unity harmonization legislation:
e documents:
RMITY
ibility of the manufacturer:
a, Sweden.
unity harmonization legislation:
e documents:
RMITY
ibility of the manufacturer:
a, Sweden.
unity harmonization legislation:
e documents:
Elvaco AB, Kabelgatan 2T, S-43437 Kungsbacka, Sweden
