model M-R6.5LCRZ.2
red label series
Home Theater Left/Center/Right
Ceiling-Mount Speaker System
www.elura.audio
Warranty
All Elura products come with a limited
li
fetime
warranty. This warranty includes
parts and labor repairs on all compo
-
nents found to be defective in material
or workmanship under normal condi
-
tions of use. This warranty shall not
apply to products which have been
abused, modified or disassembled.
A speaker that fails under conditions
other than those covered will be re-
paired at the current price of parts and
labor in effect at the time of repair. Such
repairs are warranted for 90 days from
the day of reshipment to the BUYER. If
the unit is delivered by mail, customers
agree to insure the unit or assume the
risk of loss or damage in transit.
Under no circumstances will a unit be
accepted without a return authorization
number. The warranty is in lieu of all
other warranties expressed or implied,
including without limitations, any other
implied warranty or fitness or mer-
chantability for any particular purpose,
all of which are expressly disclaimed.
Proof of sale may be required in order
to claim warranty.
Specifications
• Max. Power Handling: 5 - 100 Watts
• Sensitivity: 91dB @ 1 watt/1 meter
• Freq. Response: 50 Hz-20,000 Hz
• Driver Complement: 6
1
/
2
˝ (165mm)
compression molded talc-filled
polycarbonate cone woofer with
rubber surround
1˝ (25mm) pivoting, fluid-cooled
Tetron dome tweeter
• Nominal Impedance: 8 ohms
• Overall Dimensions: 9.25˝ (diameter)
round x 4.7˝ D (235mm x 120mm)
• Required Ceiling Cut-out: 8.25˝
(diameter) round (210mm)
New Construction
1. Determine speaker locations and
mark them on your plans for future
reference.
2. If possible, run speaker wires after
HVAC and electrical wiring is in place.
3. Secure speaker wires in place
along the run with insulated staples
only and be careful not to pierce the
wire’s insulation. Allow a bit of slack
for expansion of building materials.
4. Needless to say, the actual
speakers should not be installed
until the wall board is in place. In the
meantime, leave several feet of wire
coiled up and secured at the back
side of the mounting hole.
5. To complete the installation follow
steps 2 through 5 above.
Operational Check
After making all connections it’s a
good idea
to make sure everything is
working properly.
Turn on your sur-
round or stereo system making sure
the volume control is turned down
and that the balance control is in the
center position. Activate a music
or
movie source. Gently turn up the
volume, you should hear sound
coming from your new speakers. If
no sound is heard from any or all
speakers, switch off the system
immediately and check for
open or loose connections,
wrong polarity or shorts, or improper
source selection.
FIG. 6
FIG. 5
Continued from front
If you like the standard white finish of
your speakers, skip to step 5, but if you
want your speakers to blend in with a
colored wall or ceiling, now is the time
to paint your speaker’s perforated grille.
Remove the inner grille scrim cloth
before painting. (Grille painting hint:
Use a paint roller that is nearly out of
paint to first paint the inside of the grille,
then the outside. This will avoid paint
filling the grille perforations.)
5. Attach the wire to the input terminals
on the rear of the speaker. Remember
to maintain proper polarity with the
amplifier by attaching the positive (+)
lead to the red terminal and the negative
(-) lead to the black terminal.
6. See Fig. 6. With the speaker wire
attached to the speaker, slide the speak-
er up inside the cut-out hole. Center the
speaker in the cut-out hole and turn the
four locking screws clockwise until the
speaker is drawn up snugly to the wall
board from behind, clamping the speak-
er in place. Try to tighten each screw
equally. Replace the speaker grille by
gently placing it over the speaker until
the magnets “grab” hold of the grille.
FIG. 4
Optional back can
