manualshive.com logo in svg

ELUMEROS Colour Combat MP, Руководство пользователя, Страница: 6 / 20

Поделиться
Скачать
ELUMEROS Colour Combat MP Скачать руководство пользователя страница 6

User Manual version 1 | page 6 
Elumeros.com | Specification subject to change without notice

3. Mounting Product

The Colour Combat MP can be mounted in any orientation to a flat, non-flammable, 

structurally sound and capable surface. The fixture should be mounted away from 

flammable materials, whilst also allowing adequate airflow over and around the 

fixture at all times.
The Colour Combat MP weighs approximately 17.5Kg and as such the fixings and 

mounting surfaces should be able to support this weight, and that of any wind 

or other shear forces. There are 3 convenient holes in the fixture bracket for use 

when fixing to a surface, which can be used to mount the fixture in any position. 

Remember, this product is designed to be aimed in a direction in accordance with 

a lighting design, therefore provision needs to be made for its angular adjustment 

and care should be taken that the installation environment allows for the adequate 

tilting of the fixture. 
Please refer to Fig. 1, which shows the fixture and its mounting holes. When fixing 

to any surface, fixings should be made through holes A (left), B (centre) and C 

(right). It should be noted that installation onto certain supporting structures may 

require different fixing methods, please contact Elumeros support for assistance.
IT IS VITALLY IMPORTANT FIXING SIZES AND THE TYPE OF FIXINGS ARE SPECIFIED 

AND APPROVED BY AN APPROPRIATELY QUALIFIED AND COMPETENT PERSON!
The Colour Combat MP comes supplied with a safety fixing accessory (wire) for use 

when mounting above ground (see Fig. 2). This safety wire must be affixed to the 

fixture using the anchor hole as indicated to the right with the wire itself attached 

to an appropriate load bearing anchor that corresponds to the weight of the fixture 

with additional weight bearing capacity for any other forces that may be apparent.
The yoke of the fixture (which allows for its tilt) can be adjusted using a tool. There 

is a convenient angular dial to assist with the tilt degree of the fixture. The screw 

is indicated as shown (see Fig. 2). Care should be taken to not over tighten these 

screws, and similarly care should be taken to ensure the screws are not over 

loosened when the tilt is being adjusted.
The Colour Combat MP can also be installed onto a vertical post top with an 

appropriate pole mount adaptor as shown to the right with fixings as indicated 

(see Fig. 3). Please note that due to the weight of the Colour Combat MP, the pole 

cannot be installed upside down in a hanging position, it must only be installed 

vertically.
Please consult our technical support team for assistance with selecting the 

appropriate type of pole, flange/base plate and accessories before using this 

method of installation.

Note that this installation guide is limited to the installation of the fixture and the 

electrical connection therefore before installing the product, it is recommended 

to consult with an appropriately qualified and competent engineer to ensure the 

correctness of the intended installation method.
-  All fixings must be corrosion resistant.
-  Separation washer(s) must be installed between any part of the fixture and 

  mounting surface(s).
-  Avoid mounting the fixture in direct contact with other types of metal, as this 

  can cause galvanic corrosion. Care should be taken to ensure all fixings and 

  metal contact points will not cause galvanic corrosion. For guidance, please 

  contact Elumeros support.

 

A        B        C

Adjustable tilt

Safety fixing

accessory

(wire)

Pole bolts

Pan control

bolt

Main bolt

Fig. 1

Fig. 2

Fig. 3

Содержание Colour Combat MP





















Отзывы:

Нет отзывов