elsner elektronik Sewi KNX L Скачать руководство пользователя страница 20

Страница: 20 / 34

Parameter setting

Sensor Sewi KNX L

• Version: 10.09.2018 • Technical Changes and Errors excepted.

Set, at which deviation from the setpoint value a

dim command is to be sent

. Spe-

cify the

dimming increment

and the

repetition cycle

for the dim command.

Define, up to which

response value

the dim actuator sends a brighter or darker com-

mand. On the one hand, this defines the range of use for the lamp, on the other hand,
once the minimum or maximum value has been reached, no unnecessary messages
are sent to the bus.

The light regulation can be

interrupted during switching or dimming

by response

objects, i.e. nothing else is transmitted via the dim output. This results in manual light
operation having priority.

Set, which objects will trigger interruption and when the regulation is to be continued.

Object evaluation

• 1 = start | 0 = stop
• 0 = start | 1 = stop

Object value prior to first communication

0 • 1

Reaction to stop

• send nothing
• send off command
• send on command
• send value

Value in %

0...100

Send the dim command, if

• the actual value deviates from the set-
point value by more than X%

• the actual value deviates from the set-
point value by more than X Lux

Target / actual difference in %

(for a deviation in %)

1...100; 20

Target / actual difference in Lux

(for a deviation in Lux)

1...2500; 100

Dimmer increments

100.00% • 50.00% • 25.00% • 12.5% • 6.25% •
3.13% • 1.56%

Repetition of the dim command in seconds

1...600; 6

Dim brighter with response value in %

1...100

Dim darker with response value in %

0...99

Use interruptions

No •

Yes

Interrupt regulation when

Reception from response switching object

No • Yes

Reception from response dimming object

No • Yes

Continue regulation

• after a waiting period
• at object reception after waiting period
• at object reception or after waiting period

Waiting period in seconds

5...72000

(Standard value depending on the

setting of "continue regulation")

Object value

0 • 1 • 0 or 1

Содержание Sewi KNX L



































Результаты поиска

Содержание Sewi KNX L

Отзывы:

Похожие инструкции для Sewi KNX L

Бренды по названию

Популярные бренды

elsner elektronik Sewi KNX L, Установка и настройка

Результаты поиска

Содержание Sewi KNX L

Отзывы:

Похожие инструкции для Sewi KNX L

Бренды по названию

Популярные бренды