elsner elektronik Salva KNX basic Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 74

background image

56

Temperature and humidity parameters

Smoke alarm Salva KNX

• Version: 09.09.2016 • Technical Changes and Errors excepted.

etc.). The building protection mode may be activated with delay, which allows you to
leave the building before the controls switch to frost/heat protection mode.

General control variables

This setting appears for the control types "Heating

and

Cooling" only. Here, you can

decide whether to use a common control variable for heating and cooling. If the 2nd
level has a common control variable, you also determine the control mode of the 2nd
level here.

When using the control variable for a 4/6 way valve, the following applies:
0%...100% heating = 66%...100% control variable
OFF = 50% control variable
0%...100% cooling = 33%...0% control variable

8.3.1. Heating control level 1/2

If a heating control mode is configured, one or two setting sections for the heating le-
vels are displayed.

In the 1st level, heating is controlled by a PI control, which allows to either enter control
parameters or select predetermined applications.

In the 2nd level (therefore only in case of 2-level heating), heating is controlled via a PI
or a 2-point-control.

Setpoint frost protection (in 0.1°C)

-300…800; 70

Activation delay

less than • 5 s • ... • 5 min • … • 2 h

Setpoint heat protection (in 0.1°C)

-300…800; 350

Activation delay

less than • 5 s • ... • 5 min • … • 2 h

For heating and cooling

• separate control variables are used
• common control variables are used for
  Level 1
• common control variables are used for
  Level 2
• common control variable are used for
  Level 1+2

Use control variable for 4/6-way valve

(only for common control variables
in level 1)

No • Yes

Control type

(for level 2 only)

• 2-point-control
• PI control

Control variable of the 2nd Level is on

(only for level 2 with 2 point controlling)

• 1 bit object
• 8 bit object

«
...
55
56
57
58
59
...
»

Содержание Salva KNX basic











































































Отзывы:

Нет отзывов

Похожие инструкции для Salva KNX basic

Бренд: family first Страницы: 2

Бренд: La Crosse Technology Страницы: 23

Бренд: Southern Pride Страницы: 2

Бренд: S&S Northern Страницы: 8

Ampac Orbis IS ORB-OP-52027-APO

Бренд: Halma Страницы: 25

Бренд: Omegalink Страницы: 28

Бренд: Honda Страницы: 5

Бренд: Kinger Home Страницы: 7

Бренд: Guanxing Photoelectric Products Страницы: 9

Бренд: Clas Ohlson Страницы: 5

Бренд: Quell Страницы: 19

Бренд: Youshiko Страницы: 2

Бренд: Xpresskit Страницы: 8

Бренд: Cobra Страницы: 88

Бренд: AUTHOR Alarm Страницы: 32

Бренд: Davis & Waddell Страницы: 4

Бренд: Char-Broil Страницы: 24

Бренд: La Crosse Technology Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды